Condair Esco Скачать руководство пользователя страница 48

Страница: 48 / 52

5.3.4.2 Bell-shaped float drain for Esco stainless steel versions

• Wrap teflon tape around the thread of the straight fitting or apply silicone-free sealant (heat-

resistant up to 155 °C). Then, remove protective plug from the condensate connector of the valve

unit screw fitting into the valve unit.

• Wrap teflon tape around the thread of the angled screw coupling or apply silicone-free sealant

(heat-resistant up to 155 °C). Then, screw angled screw coupling into the bell-shaped float drain

as shown below (

the union nut must point to the top and the arrow on the bell-shaped float

drain must point in drain direction

• Slide angled screw coupling with the bell-shaped float drain onto the straight fitting until it comes

to a stop. Tighten union nut so far, that the bell-shaped float drain can not be turned by hand

anymore.

Rp 1/2"

Wrench size 22 mm

Wrench size 24 mm

Flow direction

wrap teflon tape around the thread or apply silicone-free

sealant (heat-resistant up to 155 °C)

Содержание Esco





















































Результаты поиска

Содержание Esco

Отзывы:

Похожие инструкции для Esco

Бренды по названию

Популярные бренды

Condair Esco, Руководство по установке

Результаты поиска

Содержание Esco

Отзывы:

Похожие инструкции для Esco

Бренды по названию

Популярные бренды