manualshive.com logo in svg

Condair Esco, Руководство по установке

Поделиться
Скачать
Condair Esco Скачать руководство пользователя страница 25

25

6.  Mount vertical steam distribution pipes.

•  Remove protective plugs from the sockets of the collector pipe.
•  Push vertical steam distribution pipes into the sockets of the collector pipe until they come to a 

stop (the resistance of the O-rings inside the sockets must be overcome).  Then, align nozzle 

apertures to the air flow according to drawing below. 

Note: To improve the gliding ability moisten the end of the vertical steam pipes  and the O-rings 

inside the collector sockets with water (do not use oil or grease!).

•  Screw the M5x6 grub screws (allen key 2.5 mm) provided into the sockets (as shown below), 

until they touch the vertical steam distribution pipes.

•  Vertical steam distribution pipes with a length >1400 mm must be fixed to the duct ceiling us

-

ing the brackets supplied. Before tightening the brackets vertically align steam pipes using a 
spirit level.

L

air flow direction

>200 mm

L> 1400 mm

>200 mm

<200 m

<200 mm

Air flow direction

Water

Содержание Esco





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды