Condair Esco Скачать руководство пользователя

Страница: 45 / 52

Rp 1/2"

5.3

Mounting the primary condensate drain

Important notes

– The primary condensate must be discharged separately from the secondary condensate.

– The primary condensate can either be discharged pressure-free or with a

maximum back-pressure

of 1/2 of the primary steam pressure

. The discharge/feedback of the primary condensate is

customers responsibility.

5.3.1 Thermostatic steam trap for Esco cast-iron and stainless steel versions

wrap teflon tape around the thread or

apply silicone-free sealant
(heat-resistant up to 155 °C)

Wrench size 32 mm

• Wrap teflon tape around the threads of the threaded pipe or apply silicone-free sealant (heat-

resistant up to 155 °C). Then, screw threaded pipe into the primary condensate drain (

arrow on

the condensate drain must point in drain direction

• Remove protective plug from the condensate connector of the valve unit, then screw threaded

pipe from the bottom into the valve unit.

Flow direction

admissible

mounting position

not admissible

mounting position

Содержание Esco





















































Результаты поиска

Содержание Esco

Отзывы:

Похожие инструкции для Esco

Бренды по названию

Популярные бренды

Condair Esco, Руководство по установке

Результаты поиска

Содержание Esco

Отзывы:

Похожие инструкции для Esco

Бренды по названию

Популярные бренды