Condair EL2 Скачать руководство пользователя

Страница: 60 / 72

7.6

Resetting the maintenance indication

After completing maintenance work, the

maintenance indication

(yellow LED lights) must be reset

as follows:
• Press drain key

with the unit switched off

and hold down.

• Switch on steam humidifier via the unit switch.
• Hold drain key down until the system test is completed (approx. 10 seconds).

7.5

Notes on cleaning agents

Only use cleaning agents stated in the table above

. The use of disinfectants is only permitted

if they do not leave any toxic residues. In any case the parts must be thoroughly rinsed with water

after cleaning.

WARNING!

Formic acid is indeed harmless to the skin, but it attacks the mucous membranes. Therefore prevent

your eyes and respiratory tracts from getting in touch with the acid and its vapours (wear goggles

and work in a well ventilated room or outside).

CAUTION!
Do not use any solvents, aromatized or halogenized hydrocarbons or other aggressive

substances

as they may cause damage to the components of the unit.

It is mandatory to observe and comply with the information and instructions regarding cleaning agents.

Observe in particular: all information relating to the protection of personnel, environmental protection

and restrictions regarding usage.

Содержание EL2









































































Результаты поиска

Содержание EL2

Отзывы:

Похожие инструкции для EL2

Бренды по названию

Популярные бренды

Condair EL2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание EL2

Отзывы:

Похожие инструкции для EL2

Бренды по названию

Популярные бренды