Condair EL2 Скачать руководство пользователя

Страница: 35 / 72

– Steam distribution pipe is mounted

less than 300 mm above the top edge of the humidifier

Condensate hose is led down with a

minimum slope of 20 %

, in the form of a

siphon (min.

hose bend diameter Ø200 mm)

, directly into a discharge funnel.

Note

: If your unit feeds a number of steam distribution pipes, the individual condensate hoses are

to be led into the discharge funnel.

Important!

Before putting the unit into operation, the siphon of the condensate hose must be filled

with water.

5.4.7 Inspecting the steam installation

Use the following check list to ascertain that the steam installation was performed correctly:

– Steam distribution pipe

Steam distributors (steam distribution pipe or OptiSorp steam distribution system) correctly

positioned and secured (screws tightened)?

Are the outlet orifices at right angles to the air flow direction?

– Steam hose

  Maximum length of 4 m?
  Minimum bend radius of 300 mm (4-5 x internal diameter with fixed piping)?
  Have the instructions for hose positioning been followed?
  Steam hose: no sagging (condensate pocket) or condensate drain with siphon (hose bend

with a minimum diameter of 200 mm) installed at the lowest point?

Rigid steam lines: properly insulated? Correct installation material used? Minimum internal

diameter maintained?

Steam hose(s) securely attached with clamps?
Heat expansion during operation and shortening of the hose with ageing taken into considera

tion?

– Condensate hose

  Downslope of at least 20 %?
  Siphon (min. ø200 mm) existing and filled with water?
  Condensate hose correctly fixed and not kinked?

min. 300 mm

min. 20 %

Ømin. 200 mm

min. 300 mm

min. 20 %

Ømin. 200 mm

Содержание EL2









































































Результаты поиска

Содержание EL2

Отзывы:

Похожие инструкции для EL2

Бренды по названию

Популярные бренды

Condair EL2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание EL2

Отзывы:

Похожие инструкции для EL2

Бренды по названию

Популярные бренды