Condair EL2 Скачать руководство пользователя | Manualshive

Страница: 48 / 72

background image

48

6.3.3 Inspections during operation

During operation the Condair EL2 and the humidification system have to be inspected weekly. On

this occasion check the following:
•  the water and steam installation for any leakage.
•  the steam humidifier and the other system components for correct fixing and any damage.
•  the electric installation for any damage.

If the inspection reveals any irregularities (e.g. leakage, error indication) or any damaged compo

-

nents take the Condair EL2 out of operation as described in chapter

6.5. Then, contact your Condair

representative.

6.5

Taking the unit out of operation

In order to take the steam humidifier out of operation, perform the following steps:
1. If the unit has to be switched off because of a malfunction, please note the error code (number

of flashes of the red and yellow LED) of the actual error message shown in the display.

2. Close the shut-off valve in the water supply line.

3. Start manual draining (see chapter 6.4

) and wait until the steam cylinder is empty.

4.

Actuate the unit switch.

5.

Disconnect steam humidifier from the mains

: Switch off all service switches to mains sup

-

plies (heating and control voltage) and secure switches in “off” position against accidentally being

switched on, or clearly mark the switches.

6. If

ambient temperatures

≤ 0°C

must be expected when the unit is out of operation

(operation

of the Condair

EL2

in a protective housing outside the building): drain the water supply pipe and

the water filter (filter valve).

WARNING!

Danger of burning!

If steam was produced just before the unit is taken out of operation, wait before opening the unit

and let the steam cylinder cool down to prevent danger of burning.

6.4

Carrying out manual draining

1.

Briefly press the drain/info key

. The heating voltage is interrupted and the

drain valve opens. The

yellow LED flashes

.

Note: the drain valve closes after 10 minutes automatically

2. To stop the drain cycle b

riefly press the drain/info key again

.

Proceed as follows to drain the unit manually:

«
...
46
47
48
49
50
...
»

Содержание EL2









































































Отзывы:

Нет отзывов

Похожие инструкции для EL2

Бренд: EIP Страницы: 12

Бренд: DriSteem Страницы: 40

Бренд: ProBreeze Страницы: 7

Бренд: Altech Страницы: 40

AQUARIA SLIM 10 P

Бренд: Olimpia splendid Страницы: 148

Бренд: Champion Страницы: 16

Бренд: GE Страницы: 24

Бренд: GE Страницы: 2

Appliances ADEW30

Бренд: GE Страницы: 36

Бренд: GE Страницы: 24

Бренд: GE Страницы: 28

Бренд: GE Страницы: 40

Бренд: GE Страницы: 24

Бренд: GE Страницы: 72

Бренд: GE Страницы: 2

Бренд: Damp2Dry Страницы: 16

Бренд: Kenmore Страницы: 16

Бренд: Kenmore Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды