Condair EL2 Скачать руководство пользователя | Manualshive

Страница: 46 / 72

background image

46

6.2

Commissioning

Proceed as follows when putting the unit into operation:

1.

Examine the steam humidifier and installation for possible damage

.

DANGER!

Damaged devices or devices with damaged installation may present danger to human life or

cause severe damage to material assets.

Damaged units and/or units with damaged or faulty installation must not be operated.

2.  Check whether the front panel is mounted and fixed with the two screws.
3.  Open the shut-off valve in the water supply line.
4.  Verify the set humidity value at the humidity controller or at the humidistat, and readjust as re

-

quired.

5.

Switch on the service switches

for mains supplies (heating and control voltage).

6.

Actuate the unit switch

of the steam humidifier.

The steam humidifier carries out a

system test

, during which all the LEDs light up.

If, after the system test:

–

the yellow LED lights permanently

, the steam cylinder maintenance is due (see chapter 7) or

the maintenance indication has not been reset (see chapter 7.6).

–

the red LED lights permanently

, a fatal malfunction has occurred (see chapter 8).

After the system test the unit is in normal operation mode.
As soon as the humidity controller or the humidistat requires humidity, power is switched on for

heating. The inlet valve opens (slight delay) and the steam cylinder fills with water. As soon as the

submerged electrodes heat the water up the green LED lights up and after a few minutes (approx.

5–10 minutes, depending on the conductivity of the water) steam is produced.

Note: If the Condair EL2 is operated with water of low conductivity it may happen that the maximum

steam capacity is not reached in the first few hours of operation. This is normal. As soon as the

conductivity has reached a sufficient level (due to the vaporisation process) the humidifier will reach

the maximum steam capacity.

«
...
44
45
46
47
48
...
»

Содержание EL2









































































Отзывы:

Нет отзывов

Похожие инструкции для EL2

Бренд: Calorex Страницы: 15

Бренд: Calorex Страницы: 20

WHOLE HOUSE DEHUMIDIFIER

Бренд: Unitary products group Страницы: 16

Бренд: Comedes Страницы: 127

Бренд: nedis Страницы: 44

Бренд: Bionaire Страницы: 36

Бренд: DriSteem Страницы: 18

Бренд: e-Ware Страницы: 5

Бренд: Whynter Страницы: 18

Бренд: Storch Страницы: 112

Бренд: mundoclima Страницы: 112

Бренд: Lobb Страницы: 1

Quiet comfort 758.144160

Бренд: Kenmore Страницы: 17

QUIET COMFORT 758.14417

Бренд: Kenmore Страницы: 16

QUIET COMFORT 758.14808

Бренд: Kenmore Страницы: 12

QUIET COMFORT 758.14451

Бренд: Kenmore Страницы: 16

Quiet Comfort II 758.144530

Бренд: Kenmore Страницы: 16

Бренд: Myria Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды