Comrex ACCESS 2USB Скачать руководство пользователя | Manualshive

Страница: 31 / 161

background image

31

dynaMIc addressIng

If you leave the IP type set to dynamic, there should not be additional configuration needed. The 2USB should be
assigned an IP address automatically when plugged into a network.

If you are not receiving an IP address and/or cannot establish an internet connection when you plug the unit into
a network with the DHCP addressing type selected, then you will need to contact your IT department to help
troubleshoot your network.

Tip: DHCP addresses change over time, so you may need to recheck the address if you are having trouble
connecting.

statIc addressIng

Static IPs are IP addresses that your Internet Service Provider (ISP) or IT department provides that can be assigned
to a network device. The device will always have that address when connected to the internet. When you select

Static

for your IP type, the following information fields will appear and need to be configured.

«
...
29
30
31
32
33
...
»

Содержание ACCESS 2USB


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACCESS 2USB

I-Class Mark II

Бренд: Datamax Страницы: 12

Бренд: ECO Sensors Страницы: 2

Бренд: GÄN Страницы: 24

Бренд: Banner Страницы: 10

Бренд: e-motion Страницы: 2

INDUSTRIAL Series

Бренд: QC Conveyors Страницы: 44

Бренд: Paso Страницы: 29

Бренд: Xerox Страницы: 13

Бренд: Xerox Страницы: 41

Бренд: Panasonic Страницы: 242

Бренд: Mamiya Страницы: 6

Бренд: hepco & becker Страницы: 2

STARSHOOT 52173

Бренд: Orion Страницы: 8

Allen-Bradley 42GLP-9000-QD

Бренд: Rockwell Automation Страницы: 10

Бренд: Logitech Страницы: 9

Alarm Clock Camera Case

Бренд: Wasserstein Страницы: 10

Бренд: Takex Страницы: 20

The Professional

Бренд: SLIK Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды