Comrex ACCESS 2USB Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 161

background image

121

GATEWAY SETUP

Gateway Mode involves having two networks active and enabled on ACCESS; the internet side (usually a USB-based
network) which is used to connect to the world at large, and the shared side (usually Ethernet), which is used to
connect with other computers.

The only step to Gateway Mode is setting up your shared network side with the factory default static IP address,
network mask and DHCP pool information. Navigate to

Network->Manage Networks

. Select the

Ethernet Port

from

the list, select the

Configure

button and then go to the

Locations

tab. Create a new location by selecting the

Add

button, or edit the default location. Select

IP Type,

press the

Edit

button and select

Gateway

from the dropdown

menu.

In Gateway Mode, ACCESS is acting as a DHCP server and router to the other devices. It will assign a dynamic
address to all devices connected to it on the LAN. The static address assigned to the ACCESS ethernet port is
192.168.42.1. The pool of addresses assigned by the DHCP server is 192.168.42.128 - 192.168.42.192.

«
...
119
120
121
122
123
...
»

Содержание ACCESS 2USB


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACCESS 2USB

Бренд: Wallenstein Страницы: 31

Бренд: Dancover Страницы: 31

Бренд: FEIYUTECH Страницы: 8

Бренд: FeiYu Tech Страницы: 2

Бренд: FeiYu Tech Страницы: 2

Бренд: FEIYUTECH Страницы: 26

Бренд: GARO Страницы: 23

Бренд: Watts Страницы: 8

Бренд: HALE Страницы: 44

Бренд: Sanitas Страницы: 52

Бренд: Omron Страницы: 12

Krisp Socket Assembly Kit For Straight and Offset...

Бренд: Keating Of Chicago Страницы: 1

Бренд: DEFA Страницы: 7

Бренд: Prorack Страницы: 15

ANDROID INTERFACE

Бренд: GMC Страницы: 18

Бренд: Prorack Страницы: 15

Heathkit SA-5010

Бренд: Heath Страницы: 3

Бренд: BTC Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды