Comrex ACCESS 2USB Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 161

background image

32

•

IP address

- The address for the 2USB your ISP provided. Make sure to check that nobody else

on your LAN is using this address.

•

IP Netmask (subnet mask)

- This is a series of numbers that indicates the range of your LAN

addresses. If in doubt, try 255.255.255.0.

•

IP Gateway

- The address of the Internet gateway on your account. If in doubt, try the first

three numbers of your IP address with the last digit of 1 (e.g. xxx.xxx.xxx.1).

•

IP DNS Primary

- The address for the DNS (domain name system) that will be used by the

2USB to convert alphabetical names of addresses to numerical IP addresses. Provided by your
ISP/IT department.

•

IP DNS Secondary

- The address of a backup DNS that will be used if the primary DNS fails.

The 2USB is perfectly capable of working over most LANs. However, if a LAN is heavily firewalled, subject to
overloaded traffic conditions, or has security concerns, better performance is possible if ACCESS has its own
Internet connection. Often, it’s worth the trouble to install a DSL line specifically for ACCESS, especially if the cost is
reasonable.

Since there may be bandwidth, firewall, and security concerns with installing ACCESS on a managed LAN, it is
recommended that your IT manager be consulted in these environments.

web browser

This option will open a graphical web browser and allow you to test your Internet connection by looking at a web
page. This browser does not support Flash or other complex protocols, but is suitable for basic Internet use.

Once a network connection has been established, the browser is opened by navigating to

Network -> Web

Browser.

This will open the browser into the main display window.

«
...
30
31
32
33
34
...
»

Содержание ACCESS 2USB


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACCESS 2USB

Бренд: Manfrotto Страницы: 2

Бренд: Manfrotto Страницы: 2

Бренд: AAT Страницы: 6

Бренд: Gainsborough Страницы: 2

Бренд: Gardener's Страницы: 2

Бренд: Safemate Страницы: 12

Бренд: Majestic Страницы: 4

Бренд: DRO PROS Страницы: 2

Бренд: hepco & becker Страницы: 2

STARSHOOT 52173

Бренд: Orion Страницы: 8

Allen-Bradley 42GLP-9000-QD

Бренд: Rockwell Automation Страницы: 10

SPEEDLOADER BRIDGE SYSTEM

Бренд: Floyd Rose Страницы: 10

Бренд: Ledvance Страницы: 6

Бренд: VDO Страницы: 236

Бренд: Kambrook Страницы: 12

BUNDLES S16 OPTICAL MOUSE WIRED

Бренд: PORT DESIGNS Страницы: 1

Бренд: EcoFlow Страницы: 42

Vision Premier 2393

Бренд: Kodak Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды