manualshive.com logo in svg

Compaq Professional Workstation AP400, Руководство по техническому обслуживанию и ремонту

Поделиться
Скачать
Compaq Professional Workstation AP400 Скачать руководство пользователя страница 80

4-8

    

Diagnostic Tools

Display Problems

This section identifies some quick checks for display-related problems.

Table 4-5

Solutions for Display Problems

Problem

Possible Solution

Screen is blank.

1. Monitor is not turned on and the monitor light is not on. Turn

on the monitor and check that the monitor light is on.

2. Screen save has been initiated. Press any key or move the

mouse to light the screen. Wait a few seconds for the
screen to be active.

3. Check the cable connection from the monitor to the

workstation and check the grounded AC outlet.

4. The brightness needs adjusting. Adjust the brightness

control.

5. The QuickBlank feature has been enabled through Security

Management. Run Computer Setup and disable the
QuickBlank feature.

6. The energy saver feature has been enabled. Press any key

or type the password. Wait a few seconds for the screen to
become active.

7. The RGB (Red, Green, Blue) input switch on the back of the

monitor is incorrectly set. Set the monitor’s input switch to
75 ohms. If there is a sync switch, set it to External.

8. If a fixed-sync monitor is used, be sure that the monitor can

accept the same sweep rate as the resolution chosen.

9. Check that the graphics adapter is fully and properly

inserted in the PCI or AGP slot.

Graphics colors are wrong.

1. If the BNC cable is used, make sure that the Red, Green,

and Blue BNC cables are connected to the corresponding
monitor connectors.

2. Be sure the monitor’s RGB inputs are set to 75 ohms.

Characters are dim.

1. Adjust the monitor’s brightness and contrast controls.
2. Check that the video cable is securely connected to the

video card and monitor.

3. Set the RGB switch (and sync options, if available) to 75

ohms, with the sync set to External. Refer to the
documentation included with the monitor.

Monitor does not function properly when used with the
energy saver features.

A monitor without the energy saver feature is being used
with energy saver features enabled. Disable the monitor
energy saver feature.

Blurry display or requested resolution cannot be set.

If the graphics controller was upgraded, the correct display
drivers may not be loaded. Install the correct display
drivers included in the option kit.

Continued

Содержание Professional Workstation AP400















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды