ComAp InteliLite MRS10 Скачать руководство пользователя страница 55

Страница: 55 / 65

Events specification

Protection

type

Information on binary

output available (See list

Binary outputs

)

Description

typically after downloading
new firmware or changing of
the parameter. The controller
stays in INIT mode. Check all
parameters, write at least one
new parameter.

Vgen <, >

YES

The generator voltage is out of
limits given by

Gen <V

and

Gen >V

setpoints.

Vgen unbl

The generator voltage is
unbalanced more than the
value of

Volt unbal

setpoint.

Fgen <,>

YES

The generator frequency is out
of limits given by

Gen >f

and

Gen <f

setpoints.

Igen unbl

The generator current is
unbalanced.

Overload

YES

The load is greater than the
value given by

Overload

setpoint.

Overspeed

YES

The protection comes active if
the speed is greater than

Overspeed

setpoint.

Underspeed

YES

During starting of the engine
when the RPM reache the
value of

Start RPM

setpoint

the starter is switched off and
the speed of the engine can
drop under

Start RPM

again.

Than the Underspeed
protection comes active.

EmergencyStop

If the input

Emergency stop

opened shutdown is
immediately activated.

PickupFault

Failure of magnetic pick-up
sensor for speed
measurement.

Stop fail

YES

Gen-set stop failed.

WrnServiceTime

WRN

The period for servicing is set
by the

NextServTime

setpoint.

The protection comes active if
the running hours of the
engine reach this value.

ChrgAlternFail

WRN

YES

Failure of alternator for
charging the battery.

SprinklActive

WRN

The protection is active if the
output

Sprinkler

is closed.

*Wrn RA15 fail

WRN

Warning alarm in case of lost
connection to IGL-RA15
module.

*Sd IOM fail

Shutdown alarm in case of lost
connection to IG-IOM/IGS-
PTM module.

Wrn ECU Alarm

WRN

ECU alarm list

is not empty

InteliLite – MRS10/11/15/16, SW version 2.2, ©ComAp – November 2004 55
IL-MRS-2.2.pdf

Содержание InteliLite MRS10


































































Результаты поиска

Содержание InteliLite MRS10

Отзывы:

ComAp InteliLite MRS10, Руководство пользователя, Страница: 55 / 65

Результаты поиска

Содержание InteliLite MRS10

Отзывы: