ComAp InteliLite MRS10 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 65

ComAp InteliLite MRS10 Скачать руководство пользователя страница 5

Note:

ComAp believes that all information provided herein is correct and reliable and reserves the right to
update at any time. ComAp does not assume any responsibility for its use unless otherwise expressly
undertaken.

Note:

SW and HW must be compatible (MRS10 firmware and MRS10 HW) otherwise the function wil be
disabled. If wrong software is downloaded, message HARDWARE INCOMPATIBLE appears on
controller screen. In this case use Boot load (jumper) programming – close Boot jumper and follow
instructions in LiteEdit, download correct software.
Similarly use only Chinese HW together with Chinese SW.

!!! CAUTION !!!

Dangerous voltage

In no case touch the terminals for voltage and current measurement!
Always connect grounding terminals!
In any case do not disconnect InteliLite CT terminals !

Adjust set points

All parameters are preadjusted to their typical values. But the set points in the “

Basic settings

” settings

group

!!must!!

be adjusted before the first startup of the gen-set.

!!! WRONG ADJUSTMENT OF BASIC PARAMETERS

CAN DESTROY THE GEN-SET !!!

The following instructions are for qualified personnel only. To avoid personal injury do

not perform any action not specified in this User guide !!!

InteliLite – MRS10/11/15/16, SW version 2.2, ©ComAp – November 2004 5
IL-MRS-2.2.pdf

«
...
3
4
5
6
7
...
»

Содержание InteliLite MRS10


































































Отзывы:

Нет отзывов