ComAp InteliLite MRS10 Скачать руководство пользователя страница 15

Страница: 15 / 65

Analog input item

LiteEdit

Possibility

Type Type

Not

used

Alarm

Analog input isn’t used

Analog input name

Name

Up to 14 ASCII characters

Config of input

Config

Analog

Binary (not supp. by PTM)
Tri-state (not supp. by PTM)

Analog measuring in specified
range.
Binary: open/close - threshold
750

Ω

Three-state: open/close -
threshold 750

Ω

Failure <10

Ω

or > 2400

Ω

Physical dimension

Dim

bar,%,°C, …

Up to 3 ASCII characters
(Valid only for analog inputs)

Polarity Contact

type

NC

NO

Valid only for binary and three-
state inputs
Valid only for binary and three-
state inputs

Over

Overstep. Sensor fail does not
activate protection.

Over+Fls

Overstep and Sensor fail
activates protection.

Under

Under step. Sensor fail does
not activate protection.

Protection direction

Protection

Under+Fls

Under step and Sensor fail
activates protection.

Sensor characteristic Sensor

Curve A
Curve B
Curve C

PT 1000
NI 1000
VDO Temp
VDO Press
VDO Level
4-20mA/100
4-20mA/ 60
Pt100
Ni100
0-20mA/100
4-20mA/100
0-100mV/100

iL, IOM,PTM
iL, IOM,PTM
iL, IOM,PTM

iL, IOM
iL, IOM
iL, IOM
iL, IOM,PTM
iL, IOM,PTM
iL, IOM
iL, IOM
PTM
PTM
PTM
PTM
PTM

User curve A
User curve B
User curve C

IEC 751, range -20 to 120

DIN 43760, range -20 to 120

See chapter sensor
specification
20mA/10.0Bar, ext. R 120

Ω

20mA/6.0Bar ext R 120

Ω

0-20mA/10.0Bar
4-20mA/10.0Bar

Decimal points

Dec

0, 1, 2

Number of decimal points
(Valid only for analog inputs)

User Curve A, B, C are adjustable in LiteEdit.
Each Analog input has separate set points for two level alarm setting. Analog input alarm levels and
delay adjust in

Protection

Engine protection

group.

InteliLite – MRS10/11/15/16, SW version 2.2, ©ComAp – November 2004 15
IL-MRS-2.2.pdf

Содержание InteliLite MRS10


































































Результаты поиска

Содержание InteliLite MRS10

Отзывы:

ComAp InteliLite MRS10, Руководство пользователя, Страница: 15 / 65

Результаты поиска

Содержание InteliLite MRS10

Отзывы: