manualshive.com logo in svg

ComAp InteliLite MRS10, Руководство пользователя, Страница: 44 / 65

Поделиться
Скачать
ComAp InteliLite MRS10 Скачать руководство пользователя страница 44

 

Operator interface 

Pushbuttons and LEDs, MRS10/11/15/16 

Pushbuttons 

 
 
 
 
 
 
 
 
 

 

 
 
 
 

 

 

 
 
 
 
 
 
 
 
 

1 

4 

16 

8 

17 

15 

6 

5 

2 

11 

12 

10 

9 

3 

 
1. MODE

→

  Cyclic forward selection the gen-set operation mode (OFF -> MAN -> AUT ) 

2. 

←

MODE  Cyclic backward selection the gen-set operation mode (AUT  -> MAN ->OFF ) 

3.  HORN RESET  

Deactivates the HORN 

4.  FAULT RESET  

Acknowledges faults and alarms 

5.  START 

 

Start of the gen-set 

6.  STOP 

 

Stop of the gen-set 

7.  
8.  GCB ON/OFF 

^Manual open/close of the Generator circuit breaker 

9.  PAGE 

Cyclic selection of the display mode(MEASUREMENT->ADJUSTEMENT) 

10.  Select the set point, select the screen or increase set point value 
11.  Select the set point, select the screen or decrease set point value 
12.  ENTER 

 

Confirm set point value 

LEDs 

13.  
14.  
15.  GEN VOLTAGE PRESENT: GREEN LED is on, if gen. voltage is present and within limits 
16.  GEN-SET FAILURE: RED LED starts flashing when gen-set failure occurs. After FAULT RESET 

button is pressed, goes to steady light (if an alarm is still active) or is off (if no alarm is active) 

17.  ^GCB ON: GREEN LED is on, if GCB is closed. Driven by GCB CLOSE/OPEN output. 
 
 
 

InteliLite – MRS10/11/15/16, SW version 2.2, ©ComAp – November 2004                                             44 
IL-MRS-2.2.pdf 

Содержание InteliLite MRS10


































































Отзывы:

Нет отзывов