ComAp InteliLite MRS10 Скачать руководство пользователя страница 37

Страница: 37 / 65

AnlInIOM3

lev2

[

]

The level for IOM ANALOG INPUT 3 alarm detection.
Step:

Range:

-100 - +10000

AnlInIOM3

del

[s]

Delay for IOM ANALOG INPUT 3 alarm.
Step:

1 s

Range:

0 - 180

AnlInIOM4

lev1

[

]

The level for IOM ANALOG INPUT 4 alarm detection.
Step:

Range:

-100 - +10000

AnlInIOM4

lev2

[

]

The level for IOM ANALOG INPUT 4 alarm detection.
Step:

Range:

-100 - +10000

AnlInIOM4

del

[s]

Delay for IOM ANALOG INPUT 4 alarm.
Step:

1 s

Range:

0 - 180

The protection of IOM/PTM inputs is activated by overcrossing the limits.

CalibrAInIOM 1,2,3,4

[…]

Calibrating constant to adjust the measured value of IOM/PTM analog inputs. Physical dimension of
calibrating constant is corresponding to Analog input.
Step:

Range:

-1000 – +1000

InteliLite – MRS10/11/15/16, SW version 2.2, ©ComAp – November 2004 37
IL-MRS-2.2.pdf

Содержание InteliLite MRS10


































































Результаты поиска

Содержание InteliLite MRS10

Отзывы:

ComAp InteliLite MRS10, Руководство пользователя, Страница: 37 / 65

Результаты поиска

Содержание InteliLite MRS10

Отзывы: