ComAp InteliLite MRS10 Скачать руководство пользователя страница 26

Страница: 26 / 65

Oil Press

Output closes if the oil pressure shutdown alarm activates.
The output opens, if

•

alarm is not active and

•

FAULT RESET is pressed

Oil Press Wrn

Output closes if the oil pressure warning alarm activates.
The output opens, if

•

alarm is not active and

•

FAULT RESET is pressed

Water Temp

Output closes if the water temperature shutdown alarm activates.
The output opens, if

•

alarm is not active and

•

FAULT RESET is pressed

Water Temp Wrn

Output closes if the water temperature warning alarm activates.
The output opens, if

•

alarm is not active and

•

FAULT RESET is pressed

OFF mode

The output is closed, if OFF mode is selected.

MAN mode

The output is closed, if MAN mode is selected.

AUT mode

The output is closed, if AUT mode is selected.

FuelLevel

Output closes if the Fuel level shutdown alarm activates.

FuelLevelWrn

Output closes if the Fuel level warning alarm activates.

Running

Output closes if the engine is in Running state.

ServiceTime

Output closes if the ServiceTime alarm activates.
The output opens, if

•

alarm is not active and

•

FAULT RESET is pressed

BI1..6 – stat
*BI1..8IOM - stat

The outputs give an information about the assigned binary input.
In case the assigned binary input is configured to alarm type, then the output closes when the alarm
activates. It opens if

•

alarm is not active and

InteliLite – MRS10/11/15/16, SW version 2.2, ©ComAp – November 2004 26
IL-MRS-2.2.pdf

Содержание InteliLite MRS10


































































Результаты поиска

Содержание InteliLite MRS10

Отзывы:

ComAp InteliLite MRS10, Руководство пользователя, Страница: 26 / 65

Результаты поиска

Содержание InteliLite MRS10

Отзывы: