manualshive.com logo in svg

ComAp InteliLite MRS10, Руководство пользователя, Страница: 11 / 65

Поделиться
Скачать
ComAp InteliLite MRS10 Скачать руководство пользователя страница 11

 

Power supply fusing 

A one-amp fuse should be connected in-line with the battery positive terminal to the controller and 
modules. These items should never be connected directly to the starting battery. 
Fuse value and type depends on number of connected devices and wire length.   
Recommended fuse (not fast) type - T1A. Not fast due to internal capacitors charging during power 
up.  

12VDC

+

-

Battery

+

-

-

iL-CU

HUGE

LOADS

STARTER

T1A

 

Binary output protections 

Do not connect binary outputs directly to DC relays without protection diodes, even if they are not 
connected directly to controller outputs. 
 

+

-

K1

K1

K2

K2

24VDC

+

-

controller

T1A

Fuse

Fuse

Battery

DC relays

 

 

Grounding 

To ensure proper function: 
Use as short as possible cable to the grounding point on the switchboard 
Use cable min. 2,5mm

2

  

The “-“ terminal of the battery has to be properly grounded 
 
 

InteliLite – MRS10/11/15/16, SW version 2.2, ©ComAp – November 2004                                             11 
IL-MRS-2.2.pdf 

As short 
as possible 

Содержание InteliLite MRS10


































































Отзывы:

Нет отзывов