manualshive.com logo in svg

ComAp InteliLite MRS10, Руководство пользователя, Страница: 38 / 65

Поделиться
Скачать
ComAp InteliLite MRS10 Скачать руководство пользователя страница 38

 

*ECU-controlled engine support 

There exists only one firmware branch for both standard and electronic controlled (monitored) 
engines.  
 
Presence of the ECU on the CAN bus/RS232 is configured via LiteEdit like other peripheries (iG-IOM, 

iGL-RA15). Pressing the 

 button in Configuration window of LiteEdit (version 2.0 and higher), 

opens ECU dialog window where the appropriate engine/ECU type should be selected. There are 
three groups of engine/ECU types: 

• 

Standard J1939 engines 

• 

Scania S6 

• 

Cummins-MODBUS 

 

 

 
If the connected engine is Cummins communicating via RS232, it is necessary to set the setpoint 

Basic settings

:

RS232 mode

 = CUMMINSMB. 

 
Loss of communication causes shutdown of the running engine. On the contrary, the ECU can be 
switched off at quiescent engine, that means not-communicating ECU is in that moment normal 
situation. All values from ECU shall show ####, but no alarm is displayed. The output 

ECU CommOK 

follows the real situation, that means it is not active anytime when the ECU does not communicate. 

 

The output 

ECU PwrRelay

 closes at the beginning of prestart and opens if the engine shall be 

stopped. 

 

The engine is started via standard contact output or via CAN bus (for Volvo and Scania engines). For 
other engines J1939 is used for monitoring only. 

InteliLite – MRS10/11/15/16, SW version 2.2, ©ComAp – November 2004                                             38 
IL-MRS-2.2.pdf 

Содержание InteliLite MRS10


































































Отзывы:

Нет отзывов