30
It
a
lia
n
o
E
n
g
lis
h
D
e
u
tc
h
F
ra
n
ça
is
Р
у
сс
к
и
й
Im
Im
Im
Important
portant
portant
portant
•
Countdown starts when core temperature measured by the needle probe drops below +65°C.
•
When a soft
soft
soft
soft blast chilling cycle is started, the compressor works non-stop until air temperature in the
compartment reaches ----2°C
2°C
2°C
2°C. After this, it can cycle on and off to keep this temperature constant and
prevent frost from forming.
•
The blast chilling cycle ends when the product's core temperature measured by the needle probe reaches
+3°C.
+3°C.
+3°C.
+3°C. The cycle cannot last more than 90 minutes
90 minutes
90 minutes
90 minutes.
7.2
TEMPERATURE -BASED HARD BLAST CHILLING
The temperature-based hard
hard
hard
hard blast chilling cycle is controlled by the needle probe.
Shortcut commands while in standby mode
Shortcut commands while in standby mode
Shortcut commands while in standby mode
Shortcut commands while in standby mode
1
Hard blast chilling
2
Start
Detailed commands sequence
Detailed commands sequence
Detailed commands sequence
Detailed commands sequence::::
1.
Make sure the appliance is in standby
standby
standby
standby mode (6.1
6.1
6.1
6.1).
2.
Insert the needle probe in the product to be chilled (10.0
10.0
10.0
10.0).
3.
Press button
to select the hard blast chilling cycle.
•
The led button
comes on.
•
Display DY1
DY1
DY1
DY1 gives the setpoint of the air in the compartment (----35°C
35°C
35°C
35°C).
•
Display DY2
DY2
DY2
DY2 reads “---
---
---
---”.
4.
Press button
to start the hard blast chilling cycle.
•
The led button
comes on.
•
The compressor only starts working 5555 seconds after key
is pressed (pump-down 6.4
6.4
6.4
6.4).
•
DY1
DY1
DY1
DY1 gives needle probe temperature, and DY2
DY2
DY2
DY2 the cycle time remaining, counting down from 90
90
90
90
minutes.
•
If you press button
while the cycle is running, you can view the time elapsed since it started.
5.
A buzzer sounds to advise that the blast chilling cycle has finished.
6.
At the end of the cycle, holding mode starts and continues indefinitely at a holding temperature of +3
+3
+3
+3°C
°C
°C
°C.
•
The led button
flashes.
•
If you press button
during holding time, you can view the time of the cycle just completed to see
how long it took.
•
The holding stage must last only as long as strictly necessary.
7.
To exit holding mode, press button
.
•
The led button
goes off.
•
The compressor stops 5555 seconds after button
is pressed (pump-down 6.4
6.4
6.4
6.4).
Important
Important
Important
Important
•
Countdown starts when core temperature measured by the needle probe drops below +65°C.
•
When a hard
hard
hard
hard blast chilling cycle is started, the compressor works non-stop until air temperature in the
compartment reaches ----35
35
35
35°C
°C
°C
°C. After this, it can cycle on and off to keep a constant temperature of ----2°C
2°C
2°C
2°C,
preventing the formation of frost.
•
The blast chilling cycle ends when the product's core temperature measured by the needle probe reaches
+3°C.
+3°C.
+3°C.
+3°C. The cycle cannot last more than 90 minutes
90 minutes
90 minutes
90 minutes.
7.3
TEMPERATURE -BASED BLAST FREEZING
The temperature-based blast freezing cycle is controlled by the needle probe.
Содержание W10T
