coldline W10T, Руководство по обслуживанию

Страница: 32 / 96

32
It
a
lia
n
o
E
n
g
lis
h
D
e
u
tc
h
F
ra
n
ça
is
Р
у
сс
к
и
й
•
Display DY2 DY2 DY2 DY2 reads “--- --- --- ---”.
3. Press button to select a time-based cycle.
4. Use buttons and to set the desired cycle time.
5. Press button to start the soft blast chilling cycle.
•
The led button comes on.
•
The compressor only starts working 5555 seconds after key is pressed (pump-down 6.4 6.4 6.4 6.4).
•
DY1 DY1 DY1 DY1 gives room probe temperature, DY2 DY2 DY2 DY2 the cycle time remaining.
•
If you press button while the cycle is running, you can view the time elapsed since it started.
6. A buzzer sounds to advise that the blast chilling cycle has finished.
7. At the end of the cycle, holding mode starts and continues indefinitely at a holding temperature of +3°C +3°C +3°C +3°C.
•
The led button flashes.
•
If you press button during holding time, you can view the time of the cycle just completed to see
how long it took.
•
The holding stage must last only as long as strictly necessary.
8. To exit holding mode, press button .
•
The led button goes off.
•
The compressor stops 5555 seconds after button is pressed (pump-down 6.4 6.4 6.4 6.4).
Important
Important Important Important
•
When a soft soft soft soft blast chilling cycle is started, the compressor works non-stop until air temperature in the
compartment reaches ----2°C 2°C 2°C 2°C. After this, it can cycle on and off to keep this temperature constant and
prevent frost from forming.
•
The blast chilling cycle ends when the timer completes the countdown.
8.2 TIME -BASED HARD BLAST CHILLING
The time-based hard hard hard hard blast chilling cycle is controlled by the timer.
Shortcut commands while in standby mode
Shortcut commands while in standby mode Shortcut commands while in standby mode
Shortcut commands while in standby mode
1
Hard blast chilling
2
Time-based cycle
3
Start
Detailed commands sequence Detailed commands sequence Detailed commands sequence Detailed commands sequence::::
1. Make sure the appliance is in standby standby standby standby mode (6.1 6.1 6.1 6.1).
2. Press button to select the hard blast chilling cycle.
•
The led button comes on.
•
Display DY1
DY1 DY1
DY1 gives the setpoint of the air in the compartment (----35°C
35°C 35°C
35°C).
•
Display DY2 DY2 DY2 DY2 reads “--- --- --- ---”.
3. Press button to select a time-based cycle.
4. Use buttons and to set the desired cycle time.
5. Press button to start the hard blast chilling cycle.
•
The led button comes on.
•
The compressor only starts working 5555 seconds after key is pressed (pump-down 6.4
6.4 6.4
6.4).
•
DY1 DY1 DY1 DY1 gives room probe temperature, DY2 DY2 DY2 DY2 the cycle time remaining.
•
If you press button while the cycle is running, you can view the time elapsed since it started.
6. A buzzer sounds to advise that the blast chilling cycle has finished.
7. At the end of the cycle, holding mode starts and continues indefinitely at a holding temperature of +3 +3 +3 +3°C °C °C °C.
•
The led button flashes.