background image

OWNER’S MANUAL

 

PURFIKT SPA

2021

 

13

SPA 

C

ARE 

G

UI

D

Your  authorized  dealer  carries  a  wide  variety  of  care  and 
maintenance  products.  For  more  information  please  contact  your 
Dealer.

REQUIRED FILTER MAINTENANCE 

Your  new    spa  is  equipped  with  a  filter  cartridge.  To  ensure 
maximum  water  quality  at  all  times,  you  should  replace  the  filter 
cartridge  every  six  months,  or  earlier  as  necessary.  The  filter 
cartridge  is  designed  to  be  thrown  away!  Attempts  to  re-use  the 
filter  cartridge  may  result  in  the  re-release  of  unwanted  particles 
back into the spa. 

PLEATCO DUAL CORE FILTERS 

Your spa comes with a premium filter.  Most come with equipped 
with a Pleatco DualCore Filter, which does a better job of cleaning 
your spa water than any other filter cartridge. The DualCore filter 
has  two  layers  of  filtration  media,  the  outer  layer  and  the  inner 
layer.  Both are engineered to remove different particles from your 
water.  

The  outer  core  is  similar  to  a  traditional  filter  which  traps  larger 
debris, while the inner core filters the water for particles down to 3 
microns in size.  The inner core is easily removed and both filter 
media can be cleaned.  

Keeping  your  spa  water  clean  and  refreshing  is  extremely 
important  for  your  enjoyment  of  your    spa.    Our  spas  come  with 
only the best filters available in order to ensure your satisfaction.   

REQUIRED WATER REPLACEMENT 

You  should  replace  the  spas  water  every  3-6  months.  The 
frequency  will  depend  on  a  number  of  variables  including 
frequency  of  use,  number  of  bathers  and  attention  paid  to  the 
water  quality  maintenance.  You  will  know  it  is  time  for  a  change 
when  you  can  no  longer  get  the  normal  feel  or  sparkle  to  the 
water, even though the key  water balance measurements are all 
within the recommended ranges. 

Proper water chemistry must be maintained. Your  spa

pillows are easily and quickly damaged when exposed
to  unbalanced  spa  water. 

If  you  suspect  that  your

chemicals  may  be  unbalanced,  remove  your  pillows
immediately  until  the  water  has  been  restored  to
suggested conditions.

Do not sit on the pillows

Do not pull on the pillows

Pillows should be cleaned using a soft cloth and mild soap,
then wiped with a conditioner. We recommend that pillows
be washed each time you drain you spa.

This Limited Warranty is void if  failure is caused by accident, 
acts  of  nature,  acts  of  God,  or  other  causes  beyond  the 
control  of  CSMI.  Neglect,  misuse  and  abuse  include  any 
installation, operation, or maintenance of the spa other than 
in accordance with the instructions contained in the owner’s 
manual  provided  with  the  spa,  including,  but  not  limited  to 
damage caused by operation outside the range of 34 degrees 
Fahrenheit and 116 degrees Fahrenheit or 1 degree Celsius 
and 47 degrees Celsius . 

Please be advised that the Spa Warranty will become void if 
Coast  Spas  or  any  of  its  selling  or  servicing  agents 
determines  that  the  spa  has  been  exposed  to  Hydrogen 
Peroxide, TriChlor or any substance using it as an ingredient 
proven  to  be  dangerous  to  the  Spa.  Any  condition  arising 
from the use of Hydrogen Peroxide or TriChlor on the Spa is 
an unwarrantable defect.

SPA INTERIOR 

Your  spa has a fiberglass reinforced acrylic shell. Generally 
dirt  and  stains  will  not  adhere  to  the  surface.  To  properly 
clean the surface, we recommend wiping it with a soft damp 
cloth  (or  sponge)  using  a  low  sudsing  household  soap  or 
liquid  detergent  and  rinsing  thoroughly  with  fresh  water. 
Stubborn dirt or stains may be removed by using Spic & Span 
adequately  dissolved  in  water.    Contact  your  dealer  and 
inquire about maintenance packages. 

D

O  NOT 

use any cleaning products containing abrasives or 

solvents,  since  these  could  damage  the  surface.  Harsh 
chemicals should never be used on acrylic surfaces. Damage 
to the shell due to the use of harsh chemicals is not covered 
under the warranty. 

D

O  NOT 

leave  your  spa  drained  and  in  direct  sunlight  for 

extended periods of time. Extreme heat could cause damage 

Содержание Purfikt Spa







































Отзывы: