background image

OWNER’S MANUAL

 

PURFIKT SPA

2021

 

20

LIGHTING

 ISSUES

PROBABLE CAUSE

RECOMMENDED ACTION

Standard light will not come on

 

 

Bulb has burnt out

 

Replace the light bulb 

LED lighting not in sync

 

Burnt out bulb/connection

 

Contact your dealer 

LED lighting won’t come on

Incorrect settings

 

Contact your dealer 

HEAT PROBLEMS

 

PROBABLE CAUSE

 

RECOMMENDED ACTION

 

Water will not heat

 

Error message on control panel

 

Spa is in a different Heat Mode

 

Water level is too low

 

Poor water flow

 

Closed valves

 

Pump 1 is not running

 

Refer to the Reference Card for your control 
panel to verify the error 

 

Set spa to “Standard Mode” 

 

Add water to the spa 

 

Clean filter & check valves 

 

Open all valves 

 

Contact your dealer 

Water is too hot

Incorrect reading

Filter cycle duration is too long

 

Verify temperature with thermometer 

 

Reduce duration of the filter cycle 

Water will not maintain heat

Cover is off for extended periods of time in
cold weather / cold wind.

Spa is wired for 110V and jets are on.

>

Put cover back onto spa and allow for heat to
regenerate. Call your dealer if temperature
does not increase.

>

Spa wired for 110V only have enough power
to heat or operate pumps. Turn off jets to
power heater.

PUMPS WILL NOT PRIME 

PRO

BABLE CAUSE

 

RECOMMENDED ACTION

Pump on but no water flow

 

 

Air trapped in pump

 

No water in the pump

 

Closed valves

 

Loosen bleed valve in skimmer 

 

Check the fill level in the spa 

 

Open all valves 

HYDROTHERAPY JETS

 

PROBABLE CAUSE 

RECOMMENDED ACTION

Little to no water flowing from 
jets

 

Jets turned off

 

Pump not primed

 

Valves are closed

 

Diverter set to a different seat

 

Dirty filter

 

Open jet by turning the face counter clockwise 

 

Reset breaker to allow for the spa to prime the 
pump. Open bleed valve in the skimmer area 

 

Open valves 

 

Switch diverter 

 

Remove and clean filter cartridge 

PLUMBING SYSTEM

PROBABLE CAUSE 

RECOMMENDED ACTION

Water around base of spa

 

Loose connections

 

Leak from internal fitting

 

Hand tighten all quick disconnects and fittings. 

 

Check gaskets and O-rings 

 

Contact your dealer 

Содержание Purfikt Spa







































Отзывы: