ClearSpan Storage Master Solarguard Building Скачать руководство пользователя

Страница: 11 / 51

CLEARSPAN

™

STORAGE MASTER

Revision date: 03.22.19 PB02522R6N1D

RAFTER ASSEMBLY (CONTINUED)

12. After the chord is assembled, slide one additional band

clamp (QH1402) onto each end of the chord assembly.

13. Position the assembled chord between the rafter legs

and connect the chord to the rafter as shown above.

Chord

Additional

Band Clamps

Adjustable pliers can be used to squeeze the two band

clamps if needed to thread the nut onto the bolt.

NOTE:

Remove one nut and bolt from either clamp. (It

will not be used.) The top of the chord will be about

1-1/2" down from the band clamp as shown below.

NOTE:

If the chord height needs to be lower, it can be

slid down slightly at this time.

14. Select two (2) of the 5' struts (QH1304) and two (2) of

the 7' struts (QH1308) and position them on the ground

between the upper part of the assembled rafter and the

assembled chord.

Strut pattern shown may vary slightly

from actual rafter.

1-1/2"

15. Connect one end of a 5' strut to the clamp on the rafter.

Do not tighten at this time

. (Consult the connection

details in the Quick Start section located at the back of

these instructions.)

16. Connect the other end of the same 5' strut and one end

of a 7' strut to the band clamp on the chord assembly.

Do not tighten

17. Attach the remaining end of the 7' strut to the band

clamp located near the peak of the rafter.

18. Repeat Steps 15-17 to attach the remaining struts for

this rafter assembly.

Rafter

Chord

Rafter

Содержание Storage Master Solarguard Building




















































Результаты поиска

Содержание Storage Master Solarguard Building

Отзывы:

Похожие инструкции для Storage Master Solarguard Building

Бренды по названию

Популярные бренды

ClearSpan Storage Master Solarguard Building, Инструкция по сборке

Результаты поиска

Содержание Storage Master Solarguard Building

Отзывы:

Похожие инструкции для Storage Master Solarguard Building

Бренды по названию

Популярные бренды