manualshive.com logo in svg

ClearSpan Storage Master Solarguard Building, Инструкция по сборке

Поделиться
Скачать
ClearSpan Storage Master Solarguard Building Скачать руководство пользователя страница 15

15

CLEARSPAN

™

 STORAGE MASTER

Revision date: 03.22.19    PB02522R6N1D

7.  With the purlin in position, tighten the pipe strap at the 

peak and secure the purlin in the pipe strap using a Tek 

screw.

FRAME ASSEMBLY (CONTINUED)

8.  Align the pre-marked location on the purlin with the 

center of the inside rafter to achieve the proper rafter 

spacing and tighten the cross-connector (#102546). 

NOTE:

 If needed, use a hammer to tap the cross-

connector and the purlin to center it between the 

brackets that secure the struts.

9.  After tightening the cross-connector, install a Tek screw 

(FA4482) through the cross-connector and into the 

purlin. 

Position the Tek screw so that it also secures the 

joint of the purlin pipes

. 

Tek Screw

The first purlin and the first two rafters should appear 

as shown:

10. Move down the rafters to the first rafter joint and place 

a cross-connector over the inside rafter at that joint.

11.  Select the first two sections of the second pre-marked 

purlin and install it as you did the top/center purlin.

12. Position the cross-connector and the purlin over the 

pipe joint of the rafter assembly and align the mark on 

the purlin with the center of the rafter. 

Remember:

 To prevent damage to the main cover and 

end panels, do not allow the purlin to extend beyond 

the edge of the end rafter.

Tek Screw

End Rafter

Cross Connector

Содержание Storage Master Solarguard Building




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды