ClearSpan Storage Master Solarguard Building Скачать руководство пользователя

Страница: 12 / 51

CLEARSPAN

™

STORAGE MASTER

PB02522R6N1D Revision date: 03.22.19

19. After attaching the struts and verifying that all band

clamps are tightened, secure each band clamp to the

chord using a FA4482 Tek screw.

RAFTER ASSEMBLY (CONTINUED)

Tek Screw

The assembled rafter should resemble the rafter in the

drawing shown below.

Chord

SPECIAL NOTE FOR LONGER SHELTERS:

For

longer shelters, conserve site space by assembling and

setting the rafters as you work toward the end of the

shelter.

20. Complete the next steps for END RAFTERS ONLY.

End Rafter Assembly Procedure

Complete the following steps

for the two end rafters only

1. Assemble the two end rafters on a flat surface using

the same procedure as an interior rafter.

2. Attach one pipe strap (QH1070) to each end rafter in

the locations shown below.

These pipe straps are located on the inside of the rafter

legs, underside of the rafter pipe (peak), and on top

of the chord.

Do not tighten at this time

. These will be

tightened after the purlin is installed.

NOTE:

Except for the pipe strap located at the top of

the rafter and on top of the chord, all remaining pipe

straps shown above are installed over the pipe joints at

that location.

3. Continue with the FRAME ASSEMBLY instructions that

follow.

Pipe Straps

Pipe Strap

The pipe strap is

installed over the

pipe joint on the

inside of the rafter

leg. (

End Rafters

Only

)

Pipe Joint

Top of Rafter

Содержание Storage Master Solarguard Building




















































Результаты поиска

Содержание Storage Master Solarguard Building

Отзывы:

Похожие инструкции для Storage Master Solarguard Building

Бренды по названию

Популярные бренды

ClearSpan Storage Master Solarguard Building, Инструкция по сборке

Результаты поиска

Содержание Storage Master Solarguard Building

Отзывы:

Похожие инструкции для Storage Master Solarguard Building

Бренды по названию

Популярные бренды