ClearSpan Storage Master Solarguard Building Скачать руководство пользователя

Страница: 2 / 51

CLEARSPAN

™

STORAGE MASTER

PB02522R6N1D Revision date: 03.22.19

YOU MUST READ THIS DOCUMENT BEFORE YOU

BEGIN TO ASSEMBLE THE SHELTER

Thank you for purchasing this ClearSpan™ shelter. When

properly assembled and maintained, this product will

provide years of reliable service. These instructions include

helpful hints and important information needed to safely

assemble and properly maintain the shelter. Please read

these instructions

before

you begin.

If you have any questions during the assembly, contact

Customer Service for assistance.

SAFETY PRECAUTIONS

•  Wear eye protection.
•  Wear head protection.
•  Wear gloves when handling metal tubes.
•  Use a portable GFCI (Ground Fault Circuit Interrupter)

when working with power tools and cords.

• Do not climb on the shelter or framing during or after

construction.

• Do not occupy the shelter during high winds,

tornadoes, or hurricanes.

• Provide adequate ventilation if the structure is

enclosed.

• Do not store hazardous materials in the shelter.
• Provide proper ingress and egress to prevent

entrapment.

ANCHORING INSTRUCTIONS

Prior to assembling this shelter, please read the anchoring

precautions and instructions included with the kit.

Anchoring instructions are included in the

MUST READ

document.

You must anchor the building after the frame is

assembled and before the cover is installed.

WARNING:

The anchor assembly is an integral part

of the shelter construction. Improper anchoring may

cause shelter instability and failure of the structure.

Failing to anchor the shelter properly

will void the

manufacturer’s warranty

and may cause serious injury

and damage.

LOCATION

Choosing the proper location is an important step before

you begin to assemble the structure.

The following suggestions and precautions will help you

determine whether your selected location is the best

location.
• Never erect the structure under power lines.
• Identify whether underground cables and pipes are

present

before

preparing the site or anchoring the

structure.

• Location should be away from structures that could

cause snow to drift on or around the building.

• Do not position the shelter where large loads such as

snow and ice, large tree branches, or other overhead

obstacles could fall.

SITE

After choosing a location, proper preparation of the site is

essential. The following site characteristics will help ensure

the integrity of the structure.
• The support structure must be level to properly and

safely erect and anchor the frame.

• If the site is not level, use footing to provide a secure

base for the structure. Pre-cast concrete blocks,

pressure-treated wood posts, or poured footings are all

acceptable when properly used.

• Drainage: Water draining off the structure and from

areas surrounding the site should drain away from the

site to prevent damage to the site, the structure, and

contents of the structure.

WARNING:

The individuals assembling this structure

are responsible for designing and furnishing all

temporary bracing, shoring and support needed during

the assembly process. For safety reasons, those who

are not familiar with recognized construction methods

and techniques

must seek the help of a qualified

contractor.

Содержание Storage Master Solarguard Building




















































Результаты поиска

Содержание Storage Master Solarguard Building

Отзывы:

Похожие инструкции для Storage Master Solarguard Building

Бренды по названию

Популярные бренды

ClearSpan Storage Master Solarguard Building, Инструкция по сборке

Результаты поиска

Содержание Storage Master Solarguard Building

Отзывы:

Похожие инструкции для Storage Master Solarguard Building

Бренды по названию

Популярные бренды