ClearSpan Storage Master Solarguard Building Скачать руководство пользователя страница 34

Страница: 34 / 51

CLEARSPAN

™

STORAGE MASTER

PB02522R6N1D Revision date: 03.22.19

PREPARE MAIN COVER

Gather the parts:
•  Pipe 1.315" x 75" swaged
•  Pipe 1.315" x 73.5" plain
•  Main cover
•  Tek screws

Assembly Procedure

NOTE:

When handling the main cover and setting it in position, do not pull on the end straps. They will pull out of the

cover. Position the pre-installed straps of the main cover at the ends of the assembled and anchored frame.

WARNING:

To prevent damage to the cover and to prevent serious personal injury, DO NOT attempt to install the

main cover on windy days.

1. Assemble two main cover conduits. Start each conduit assembly with one (1) plain pipe and add swaged pipes to

arrive at the correct length.

This conduit is identical to the length of the purlin pipe assemblies.

NOTE:

Duct tape over the Tek screws to prevent damage to main cover.

These cover conduits are inserted into the pockets sealed into the main cover. The conduits are used to tighten and

secure the main cover.

2. After assembling the cover conduits, locate the main cover and unfold it on a clean, smooth surface near the frame.

NOTE:

Unfold the main cover with the inside surface facing up.

3. Locate the cover ends with strapping and align with the front and back of the shelter.
4. Insert the cover conduits into the pockets of the main cover.

a. Locate all sections of pipe needed to assemble

the cover conduit.

b. Insert the swaged end of each pipe into the

plain end of another pipe until the conduit is

assembled.

c. Secure each pipe joint with a Tek screw.

Cover Conduits

Cover

Ends w/

Strapping

Содержание Storage Master Solarguard Building




















































Результаты поиска

Содержание Storage Master Solarguard Building

Отзывы:

Похожие инструкции для Storage Master Solarguard Building

Бренды по названию

Популярные бренды

ClearSpan Storage Master Solarguard Building, Инструкция по сборке

Результаты поиска

Содержание Storage Master Solarguard Building

Отзывы:

Похожие инструкции для Storage Master Solarguard Building

Бренды по названию

Популярные бренды