ClearSpan Storage Master Solarguard Building Скачать руководство пользователя

Страница: 46 / 51

CLEARSPAN

™

STORAGE MASTER

PB02522R6N1D Revision date: 03.22.19

Door Jamb Addendum

ADDITIONAL 111708 BRACKET INSTALLATION

FOR DOOR JAMBS (Door Installation Only.)

In addition to the standard door jamb and end frame

installation instructions presented in this guide, please

install the 111708 connection brackets as described

below.

These brackets are not shown in any of the

main building diagrams in this manual.

Use the

diagrams on this page for proper bracket placement

and installation.

NOTE:

The door jambs are the vertical frame members

that the door is attached to when it is installed.

Complete these steps:
1. Locate the 111708 brackets and FA4482B Tek

screws included with the building.

2. After installing the door jambs and end wall

framing, bend each 111708 bracket as needed to

install.

ATTENTION:

Brackets are shipped as flat plates.

Bend each one as needed to attach to the end

rafter support. To bend the plate, tightly clamp it

in a vise so the bend point is centered between

the mounting holes. Lightly tap the free end of

the plate with a small maul until the 90° angle is

created.

3. Use four (4) FA4482B Tek screws to attach each

111708 bracket.

Brackets are used to secure

the door jambs only. Do not use these for any

other vertical frame member of the end wall.

See diagrams below for your end frame.

Diagrams show the locations of the door jambs. Circles show where to attach the 111708 brackets.

Storage Master End Frame Designs: 1-Door & 2-Door

Jambs

Ground Level

111708

Bracket

Door

Jamb

FA4482B

Tek Screws

111708 Bracket

Rafter Support

Band Clamp

Door Jamb and Band Clamp: Install one 111708 bracket

on each side of each door jamb.

111708

Bracket

FA4482B Tek

Screw

Door

Jamb

Rafter Support

Band Clamp

104074

Содержание Storage Master Solarguard Building




















































Результаты поиска

Содержание Storage Master Solarguard Building

Отзывы:

Похожие инструкции для Storage Master Solarguard Building

Бренды по названию

Популярные бренды

ClearSpan Storage Master Solarguard Building, Инструкция по сборке

Результаты поиска

Содержание Storage Master Solarguard Building

Отзывы:

Похожие инструкции для Storage Master Solarguard Building

Бренды по названию

Популярные бренды