manualshive.com logo in svg

ClearSpan Storage Master Solarguard Building, Инструкция по сборке

Поделиться
Скачать
ClearSpan Storage Master Solarguard Building Скачать руководство пользователя страница 28

CLEARSPAN

™

 STORAGE MASTER

28

PB02522R6N1D    Revision date: 03.22.19

NARROW JAMB BRACKET INSTALLATION

 (14' x 11' Doors)

Use these instructions to install the Narrow Jamb Bracket (107591) for the 

14' x 11' roll-up door

. The jamb brackets and 

the 3/8" mounting bolts, lock washers, and nuts are shipped with the hardware for the building.  

1.  Locate one 107591 narrow jamb bracket and two (2) 

3/8" x 3" hex bolts, two (2) 3/8" lock washers, and two 

(2) 3/8" nuts.

2.  From outside the end wall frame, position the bracket 

as shown. 

View shows the door frame and jamb bracket 

as seen 

from the outside

 of the assembled end wall. The back 

or inside surface of the jamb bracket will be flush with 

the back of the door jamb when properly installed.

107591

Rafter Chord

Door Jamb

Header

Narrow Jamb 

Bracket 

locations for

14' x 11' door. 

Diagram shows 

end wall as seen 

from the outside.

3.  Use the bracket as a template, mark two (2) holes, and 

drill these through the door jamb using a 3/8" drill bit. 

NOTE:

 The upper part of the bracket sets behind the 

chord of the end rafter. Use any two (2) of the four (4) 

3/8" mounting holes to secure the brackets.

4.  Insert the bolts through the holes, add a lock washer 

and nut to each, and tighten the bolts.

 

Tools and materials needed per door: 
•  Two (2) 107591 Narrow Jamb Brackets
•  3/8" drill bit and drill
•  Wrenches or socket and ratchet set
•  3/8" x 3" Hex head bolts (4) 
•  3/8" nuts (4) and 3/8" lock washers (4)

NOTE:

 The jamb brackets support the door and roll-up 

mechanism. Refer to the door manufacturer's installation 

instructions to attach the door support brackets and the 

door to the 107591 jamb brackets. One 107591 bracket is 

attached to each upper corner of the door frame as shown 

below. The installation of the jamb bracket for the left side 

of the door frame is shown. Repeat the instructions to 

install the right bracket. 

See the End Wall Diagram–Front 

for additional details.

Follow these instructions to attach the 107591 brackets:

5.  Repeat the steps to install the remaining bracket.
6.  Continue with these instructions.

ATTENTION:

 

Align the bottom 

of the bracket 

with the center of 

the door header.

Center line of 

the header.

Chord

Secure to 

door jamb 

using 3/8" 

bolts, lock 

washers, 

and nuts.

As seen 

from the 

outside.

Содержание Storage Master Solarguard Building




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды