ClearSpan Storage Master Solarguard Building Скачать руководство пользователя

Страница: 50 / 51

CLEARSPAN

™

STORAGE MASTER

PB02522R6N1D Revision date: 03.22.19

POL

YCOR™ INST

ALLA

TION DIAGRAM

4' x 8'

Door

Each panel is cut from a

4' x 8' sheet of PolyCor™.

Install the pedestrian door

before

installing the PolyCor™ panels around the door

ATTENTION:

DO NOT

install H-channel to

the PolyCor™ panels around the 14' x 1

door opening. See dashed lines.

NOTE:

Attach the upper panels and the outside

panels (

) to the end wall frame and then trim

the panels to the required length or width.

Install H-Channel around the pedestrian door to finish the edge.

ATTENTION:

The

lines

identify the locations of H-Channel. Install H- Channel between all PolyCor™ panels.

Use F

A4474

Tek screws

and neo-bonded washers to secure panels to frame.

Install F

A4474

Tek Screws and W

ashers along the

perimeter of the end wall panels and apply tape over the screw heads to protect the main cover when it is installed.

Содержание Storage Master Solarguard Building




















































Результаты поиска

Содержание Storage Master Solarguard Building

Отзывы:

Похожие инструкции для Storage Master Solarguard Building

Бренды по названию

Популярные бренды

ClearSpan Storage Master Solarguard Building, Инструкция по сборке

Результаты поиска

Содержание Storage Master Solarguard Building

Отзывы:

Похожие инструкции для Storage Master Solarguard Building

Бренды по названию

Популярные бренды