ClearSpan Storage Master Solarguard Building Скачать руководство пользователя

Страница: 17 / 51

CLEARSPAN

™

STORAGE MASTER

Revision date: 03.22.19 PB02522R6N1D

FRAME ASSEMBLY (CONTINUED)

ATTENTION:

The last rafter to place in position will

be the remaining end rafter. This end rafter includes

the pipe straps attached during the rafter assembly

procedures and is identical to the first end rafter set in

place.

22. Set the end rafter in place and align the purlins with the

pipe straps (previously attached to the rafter). Insert the

rafter feet mounting bolts (bolt head to the outside) and

tighten as previously instructed.

23. Begin with the top pipe strap and ensure that

approximately half an inch of the purlin extends through

the pipe strap and tightened the pipe strap mounting

bolts.

24. Verify that the end rafter is plumb.

NOTE:

If the rafter is not plumb (straight up and down)

and more of the purlin pipe needs to extend through

the pipe strap and beyond the edge of the rafter, it may

be necessary to cut the purlin to the required length.

To prevent cover damage,

do not allow the purlin to

extend beyond the edge of the rafter

25. With all rafters in place and the top five (5) purlins

installed and tightened, return to the rafter feet and

tighten the main bolt that attaches the bottom plate of

the rafter foot to the upper portion of the foot.

26. Complete the ATTACH THE BOTTOM and ATTACH

THE CHORD PURLIN procedures that follow.

ATTACH THE BOTTOM PURLINS

After the top five (5) runs of purlins are in place and secure,

complete these steps to install the remaining purlins.

Required tools:
• Tape measure
• Permanent marker

ATTENTION:

The bottom purlins run on the inside of the

rafter legs near the bottom of those rafter legs.
1. Begin at one end of the frame assembly and measure

up 13 1/2" from the rafter foot mounting plate on the

end rafter and make a mark on the inside of the rafter

leg.

NOTE:

This mark and the remaining marks identify the

location of the bottom purlin for each side.

The mark

identifies the center of the purlin

2. After marking the end rafter, attach a pipe strap to the

inside of the rafter leg so that the strap is positioned

with the mark at its center. Do not tighten the strap Tek

screws at this time.

3. Move to the remaining leg on the same rafter assembly

and mark as instructed in the previous steps.

4. Repeat Steps 1-3 for the remaining end rafter

assembly.

5. On the first inside rafter assembly, measure the same

distance (13-1/2") up the rafter leg from the foot base

and make a mark on the outside of the leg.

13-1/2"

Содержание Storage Master Solarguard Building




















































Результаты поиска

Содержание Storage Master Solarguard Building

Отзывы:

Похожие инструкции для Storage Master Solarguard Building

Бренды по названию

Популярные бренды

ClearSpan Storage Master Solarguard Building, Инструкция по сборке

Результаты поиска

Содержание Storage Master Solarguard Building

Отзывы:

Похожие инструкции для Storage Master Solarguard Building

Бренды по названию

Популярные бренды