Package Contents
Warnings and Cautions
1of2
For Style BST8407MB
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Crossbar
Assembly
x 1
Please go to
for product cleaning tips. Go to the
selection.
(1) A19 Medium Base Bulb 100W Maximum, Medium Base Vintage Bulb is recommended, bulb not included.
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact your original place of purchase.
www.quoizel.com
Care + Maintenance
Light Source:
Estimated Assembly Time:
Preparation:
Fixture can only be mounted in the direction indicated on page 2.
Tools Required:
Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Fixture Body
x 1
C
(Step 2 Continued)
out of the crossbar until the correct length is achieved. Once the
backplate and Fixture Body (E) is secure, remove the mounting ball
and Fixture Body (E).
Installation Guide #IS-BST8407MB
2018 QuoizelInc.
ReleasedDate:2018-09-17
visit us on-line at www.quoizel.com
B
Alternate
Mounting screw
x 2
STEP 2
Test Fit the Backplate to the Crossbar Assembly
-
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (E) onto the Crossbar Assembly (A)
and secure with mounting balls. Note: The backplate and Fixture
Body (E) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screws
on the Crossbar Assembly (A) by unscrewing the preassembled hex
nut and lock washer and then screwing the mounting screws in or
E
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Figure 2
E
Mounting Screw
or Alternate Short
Mounting Screw
Lock screw
x 2
Arm
x 1
D
Cage with
Glass Shade
x 1
F
Figure 1
STEP 1
Installing the Crossbar Assembly
-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Mounting Screw
or Alternate Short
Mounting Screw
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
STEP 3 - Install Arm, Bulb and Cage with Glass Shade
A. Remove the lock ball from the top edge of the backplate.
B. Place the scroll end of the Arm (D) into the loop and attach the other
end of the Arm (D) over the bolt on the backplate and secure with
previously removed lock ball. Hand tighten until snug.
C. Insert the bulb onto the socket and screw snugly into place.
D. Place the Cage with Glass Shade (F) over the bulb and socket.
E
F
Vintage Bulb
(recommended
but not included)
C
Neck of Socket Cup
D
Lock Ball
Bolt
Backplate
Figure 3
(Scroll End)
Loop
Socket
