ClearSpan PB00010R4N Скачать руководство пользователя | Manualshive

Страница: 4 / 29

background image

CLEARSPAN

™

STORAGE MASTER

4

Revision date: 05.08.19

REQUIRED TOOLS

The following list identifies the main tools needed to

assemble the shelter. Additional tools and supports may be

needed depending on the structure, location, and

application.
• Tape measure or measuring device
• Variable speed drill and impact driver (cordless with

extra batteries works best)

•  Wrenches or ratchet and socket set (recommended)
•  Scissors or utility knife
•  Ropes long enough to reach over the shelter
•  Hammers, gloves, and eye protection
•  Metal file and metal cutting saw
•  Duct tape
•  Ladders, work platforms, and other machinery for lifting

designed to work safely at the height of the shelter

UNPACK AND IDENTIFY PARTS

The following steps will ensure that you have all the

necessary parts before you begin to assemble the shelter.
1. Unpack the contents of the shipment and place where

you can easily inventory the parts. Refer to the Bill of

Materials/Spec Sheets.

2. Verify that all parts listed on the Bill of Materials/Spec

Sheets are present. If anything is missing or you have

questions, consult the Pictorial Parts Guide and all

shelter diagrams for clarification, or contact Customer

Service.

NOTE:

At this time, you do not need to open the plastic

bags containing smaller parts such as fasteners or

washers.

QUICK START GUIDE

For a quick overview of this shelter and its components,

consult the Quick Start Guide at the back of these

instructions.

Space below is reserved for customer notes.

«
...
2
3
4
5
6
...
»

Содержание PB00010R4N






























Отзывы:

Нет отзывов

Похожие инструкции для PB00010R4N

HOOLIGAN 2000001591

Бренд: Coleman Страницы: 2

Бренд: Harbor Freight Tools Страницы: 20

Бренд: AC Infinity Страницы: 24

Бренд: skandika outdoor Страницы: 4

Canopy Gotland 4

Бренд: Skandika Страницы: 2

Бренд: Black Diamond Equipment Страницы: 50

Бренд: Ozark Trail Страницы: 6

CAMPO CASA XT 5P

Бренд: Vaude Страницы: 59

Бренд: XL displays Страницы: 7

Бренд: ARB Touring Страницы: 12

Бренд: Napier Страницы: 7

Бренд: Vango Страницы: 3

ProShed MS572012

Бренд: Dancover Страницы: 42

Бренд: Tarasola Страницы: 12

Бренд: Vaude Страницы: 59

Traditional One Piece Party Canopy

Бренд: Camelot Страницы: 2

Бренд: Quictent Страницы: 28

Бренд: ClearSpan Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды