Harbor Freight Tools CoverPro 62860 Скачать руководство пользователя страница 1

Страница: 1 / 20

Vehicle not included.

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected]

WARNING! TO PREVENT SERIOUS

INJURY: Do not start or operate any internal

combustion engine inside or near Shed.

Owner’s Manual & Safety Instructions

Save This Manual

Keep this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the

back of the manual near the assembly diagram (or month and year of purchase if product has no number).

Keep this manual and the receipt in a safe and dry place for future reference.

23b

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-888-866-5797 as soon as possible.

2023 by Harbor Freight Tools

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Содержание CoverPro 62860





















Результаты поиска

Содержание CoverPro 62860

Отзывы:

Похожие инструкции для CoverPro 62860

Бренды по названию

Популярные бренды

Harbor Freight Tools CoverPro 62860, Руководство пользователя

Результаты поиска

Содержание CoverPro 62860

Отзывы:

Похожие инструкции для CoverPro 62860

Бренды по названию

Популярные бренды