ClearSpan PB00010R4N Скачать руководство пользователя

Страница: 8 / 29

CLEARSPAN

™

STORAGE MASTER

Revision date: 05.08.19

RAFTER ASSEMBLY (CONTINUED)

3. With the main rafter pipes seated at each joint and the

rafter positioned on a flat surface, secure each joint

with a single self-tapping Tek screw. Position Tek screw

approximately 1'' from pipe joint.

ATTENTION:

Install the screws so they will not touch

the cover once it is installed. This is typically on the

backside of the rafter, which will be the surface visible

from the

inside

of the shelter once the frame is

assembled.

4. Assemble all rafters as described except for two (2)

and continue with the additional steps to assemble the

two end rafters.

END RAFTER ASSEMBLY

Complete the following steps

for the end rafters only

1. Assemble the two end rafters on a flat surface.

NOTE:

Do not install Tek screws into the rafter joints at

this time.

2. Slide six (6) end clamps (102857) and two (2) band

clamps (QH1404) onto the rafter in the locations noted

below. (Do not secure the clamps to the rafter at this

time. These clamps will be repositioned during the

frame assembly when the purlins are added.)

NOTE:

Position all clamps as shown. Use a piece of

duct tape to keep the clamps from sliding when the

rafter is set in place (if needed).

View below shows how to position all end clamps to

prepare for the frame assembly.

ATTENTION:

All purlins run on the inside of the frame.

3. Repeat the procedure for the remaining

end rafter

4. Continue with the FRAME ASSEMBLY instructions that

follow.

1˝

Tek screw

102857

Toward the inside

of the frame when

assembled.

102857

Содержание PB00010R4N






























Результаты поиска

Содержание PB00010R4N

Отзывы:

Похожие инструкции для PB00010R4N

Бренды по названию

Популярные бренды

ClearSpan PB00010R4N, Руководство пользователя

Результаты поиска

Содержание PB00010R4N

Отзывы:

Похожие инструкции для PB00010R4N

Бренды по названию

Популярные бренды