background image

15

CLEARSPAN

 STORAGE MASTER

Revision date: 05.08.19

END PANEL INSTALLATION

The following procedure describes installing an end panel. 

NOTE:

 The end wall shown in the diagrams that follow may 

differ in design and size. The steps to install the basic end 

panel are the same despite these obvious differences.

Required parts include:
•  QE00010NZ0 end panels 
•  FAMF01B washers
•  FA4482B Tek screws
•  CC6214 fabric clips (Divide the quantity in half and use 

half for each end panel.)

Complete these steps to install a typical end panel:
1.  Spread an end panel out on the ground (pocket side up 

if applicable) and center the end panel as needed.

2.  With the proper lift (or ladders) positioned inside the 

frame and with assistance, pull the end panel up and 

over the top of the end rafter. Square the end panel on 

the end frame and verify that the bottom edge is in the 

desired position. 

 

NOTE:

 This procedure describes attaching the panel 

bottom to the base rail using Tek screws and washers. 

The end panel can also be pulled under and secured 

to the inside surface of the base rail using the same 

fasteners. 

This installation is not shown. 

 

If a pocket is present along the bottom edge of the 

panel, the end wall base rail tubes can be detached, 

fed into the pocket and reattached to the end wall 

frame. Trim the cover pocket to get the best fit if 

needed.

3.  With the lower edge of the end panel in the desired 

position, secure the top end of the panel to the 

backside of the end rafter 

using a few fabric clips and 

Tek screws

 DO NOT ATTEMPT 

TO PULL THE END 

PANEL INTO POSITION 

ON WINDY OR STORMY 

DAYS!

NOTE:

 These fasteners are used to temporarily hold 

the end panel in place while the lower edge is secured 

to the base rail.

4.  With the top edge temporarily secured to the end 

rafter, move to the bottom of the panel and stretch and 

secure the edge to the base rail using Tek screws and 

washers. 

 

NOTE:

 Space the fasteners evenly along the base rail 

at 24" intervals.

5.  With the panel secured along the bottom, loosen the 

temporary clips (installed in Step 3) and stretch the end 

panel up and over the end rafter. (Additional assistants 

are needed to keep the panel evenly stretched.)

6.  Attach the fabric clips to secure the end panel to the 

rafter. Evenly space the fabric clips at 24" intervals. 

Keep the panel evenly stretched as you work along the 

rafter and down to the base rail.

Frame shown above differs from actual frame in design.

End Panel

View shows the inside surface 

of the end panel.

7.  For the non-door end of the shelter, use Tek screws 

and washers to secure the end panel to the vertical end 

wall framing of the shelter.  

 

NOTE:

 Evenly space the Tek screws and washers as 

needed. (See the diagram at the top of this column and 

the diagram on Page 17 under Step 2.) 

8.  After installing both end panels, return to the door end 

of the frame and cut the opening for the roll-up door.

Содержание PB00010R4N






























Отзывы: