ClearSpan PB00010R4N Скачать руководство пользователя

Страница: 20 / 29

CLEARSPAN

™

STORAGE MASTER

Revision date: 05.08.19

8. Thread the strap ends into the ratchet and slightly

tighten.

ATTACH MAIN COVER (CONTINUED)

NOTE:

It may be necessary to remove excess strap if it

binds up in the ratchet.

9. Repeat the steps for the remaining ratchets.
10. Using additional help (if needed) tighten the main cover

beginning with the ratchets along the side of the shelter

frame.

11. After the side ratchets are tightened, return to the end

wall ratchets and tighten the bonnet straps of the main

cover.

NOTE:

Loosen the ratchets if needed to remove

excess strap and retighten. Loosen all ratchets if

needed to reposition the main cover on the frame and

retighten the ratchets.

12. Fold the skirt of main cover down and over the ratchets

to complete the installation of the main cover.

SHELTER CARE AND MAINTENANCE

Proper care and maintenance of your shelter is important.

Check the following items periodically to properly maintain

your shelter:
• Regularly check the main cover and panels to see that

these remain tight and in proper repair.

• Check connections and all fasteners to verify that they

remain tight.

• Do not climb or stand on the shelter at anytime.
• Remove debris and objects that may accumulate on

the shelter. Use tools that will not damage the cover

when removing debris.

• Remove snow to prevent excess accumulation. Use

tools that will not damage the cover when removing

snow.

• Check the contents of the shelter to verify that

nothing is touching the cover or the side panels that

could cause damage.

• Check the anchoring system to ensure that all

components are tight and in good repair.

• If the shelter is moved, inspect all parts and

connections before reassembling.

• For replacement or missing parts, call 1-800-245-9881

for assistance.

NOTE:

With the exception of Truss Arch buildings,

ClearSpan™ shelters and greenhouses

do not

have any

tested loading criteria.

Содержание PB00010R4N






























Результаты поиска

Содержание PB00010R4N

Отзывы:

Похожие инструкции для PB00010R4N

Бренды по названию

Популярные бренды

ClearSpan PB00010R4N, Руководство пользователя

Результаты поиска

Содержание PB00010R4N

Отзывы:

Похожие инструкции для PB00010R4N

Бренды по названию

Популярные бренды