ClearSpan PB00010R4N Скачать руководство пользователя

Страница: 18 / 29

CLEARSPAN

™

STORAGE MASTER

Revision date: 05.08.19

a. Locate all sections of pipe needed to assemble

the cover conduit.

b. Insert the swaged end of each pipe into the

plain end of another pipe until the conduit is

assembled.

c. Secure each pipe joint with a Tek screw.

Cover Conduits

Cover

Ends w/

Strapping

Frame shown without end panels for clarity.

PREPARE MAIN COVER

Gather the parts:
•  Main cover
•  Pipe 1.315" x 75" swaged
•  Pipe 1.315" x 73.5" plain
•  Ratchets (QH1061)
•  Tek screws

Assembly Procedure

NOTE:

When handling the main cover and setting it in

position, do not pull on the end straps. They will pull out of

the cover.

WARNING:

To prevent damage to the cover and to

prevent serious personal injury, DO NOT attempt to

install the main cover on windy days.

1. Fasten a ratchet to the end conduit using a Tek screw

in the bottom hole of the ratchet as shown below.

NOTE:

Install the ratchet about 6" in from the end rafter

leg and through the installed end panel.

2. Repeat this step at all remaining corners.

3. Assemble two main cover conduits. Start each conduit

assembly with one (1) plain pipe and add swaged pipes

to arrive at the correct length.

NOTE:

Use duct tape to tape the Tek screws to prevent

damage to main cover.

Cover conduits are inserted into the pockets sealed

into the main cover. The conduits are used to tighten

and secure the main cover.

4. After assembling the cover conduits, locate the main

cover and unfold it on a clean, smooth surface near the

frame.

NOTE:

Unfold the main cover with the inside surface

facing up.

5. Locate the cover ends with strapping and align with the

front and back of the shelter.

6. Insert the cover conduits into the pockets of the main

cover.

Tek screw

Ratchet

Содержание PB00010R4N






























Результаты поиска

Содержание PB00010R4N

Отзывы:

Похожие инструкции для PB00010R4N

Бренды по названию

Популярные бренды

ClearSpan PB00010R4N, Руководство пользователя

Результаты поиска

Содержание PB00010R4N

Отзывы:

Похожие инструкции для PB00010R4N

Бренды по названию

Популярные бренды