ClearSpan PB00010R4N Скачать руководство пользователя

Страница: 28 / 29

CLEARSPAN

™

STORAGE MASTER

Revision date: 05.08.19

Door Jamb Addendum

ADDITIONAL 111708 BRACKET INSTALLATION FOR

DOOR JAMBS (Door Installation Only.)

In addition to the standard door jamb and end frame

installation instructions presented in this guide, please

install the 111708 connection brackets as described below.

These brackets are not shown in any of the main

building diagrams in this manual.

Use the diagrams on

this page for proper bracket placement and installation.

NOTE:

The door jambs are the vertical frame members that

the door is attached to when it is installed.

Complete these steps:
1. Locate the 111708 brackets and FA4482B Tek screws

included with the building.

2. After installing the door jambs and end wall framing,

bend each 111708 bracket as needed to install.

ATTENTION:

Brackets are shipped as flat plates. Bend

each one to conform to the angle created by the rafter

curve. To bend the plate, tightly clamp it in a vise so the

bend point is centered between the mounting holes.

Lightly tap the free end of the plate with a small maul

until the desired angle is reached.

3. Use four (4) FA4482B Tek screws to attach each

111708 bracket to the end rafter and top of each door

jamb.

Brackets are used to secure the door jambs

only. Do not use these for any other vertical frame

member of the end wall. See diagram—lower right.

4" x 4" Door Jamb and Band Clamp: Install one

111708 bracket on each side of each door jamb.

111708

Bracket

FA4482B Tek

Screw

4" x 4"

Door

Jamb

End Rafter

Band Clamp

1.5" x 1.5" or 2" x 2" Door Jamb and 104074

Square-to-Round Tube Bracket: Install one 111708

bracket on each side of each door jamb.

111708

Bracket

FA4482B Tek

Screw

Door

Jamb

104074

End Rafter

Band Clamp

111708

Bracket

Door

Jamb

FA4482B

Tek Screws

111708

Bracket

Diagram shows the location of the door jambs.

Circles show where to attach the 111708 brackets.

Jambs

Ground Level

Содержание PB00010R4N






























Результаты поиска

Содержание PB00010R4N

Отзывы:

Похожие инструкции для PB00010R4N

Бренды по названию

Популярные бренды

ClearSpan PB00010R4N, Руководство пользователя

Результаты поиска

Содержание PB00010R4N

Отзывы:

Похожие инструкции для PB00010R4N

Бренды по названию

Популярные бренды