ClearSpan PB00010R4N Скачать руководство пользователя

Страница: 19 / 29

CLEARSPAN

™

STORAGE MASTER

Revision date: 05.08.19

ATTACH MAIN COVER

Gather the parts:
• Main cover (with conduits already inserted)
• Ropes long enough to reach over the frame (provided

by customer)

• Ratchets (QH1061) and 103620B straps
• Tek screws and utility knife (or similar cutting tool)

Assembly Procedure
1. Divide the remaining number of ratchets in half. Place

the ratchets on the ground next to the rafter where they

will be attached. See Side Profile diagram.

NOTE:

Ratchets are evenly spaced long each side of

the shelter and directly across from each other on the

same rafter assembly

. Rafters are identified by the

arrows above.

2. To pull the cover over the frame, attach ropes to both

ends of the cover conduit. Wrap the rope around the

conduit a few times to prevent it from slipping off.

3. With all ropes attached to the cover conduit, lift the

conduit and carry the cover toward the base of the

frame.

4. Toss the ropes over the frame and pull the cover into

position. One person is required at each rope.

5. Once the main cover is pulled into position, center the

cover on the frame and remove the ropes. Loosely

secure the ends of the cover to the ratchets

attached

to the base rail of the end wall framing (previous

procedure).

ATTENTION:

Do not tighten the straps at this time

6. Using the main cover conduit and strap length as

guides, attach the ratchets to the rafters at the proper

height. Fasten ratchets to the outside (or inside if

desired) of the rafters using Tek screws.

7. Lift the cover skirt and cut a slit in the cover conduit

pocket at the rafter position. Insert a 3' section of strap

through the slit and around the cover conduit.

Ropes

Cover

Conduit

Frame shown without end panels for clarity.

NOTE:

Depending on the length of the cover it may

be necessary to attach additional ropes to the cover

conduit between the end ropes by cutting a small

opening in the cover pocket and tying the rope around

the conduit. DO NOT cut through the main cover.

Cut

through the conduit pocket only.

NOTE:

DO NOT cut through the main cover.

Cut

through the conduit pocket only.

Содержание PB00010R4N






























Результаты поиска

Содержание PB00010R4N

Отзывы:

Похожие инструкции для PB00010R4N

Бренды по названию

Популярные бренды

ClearSpan PB00010R4N, Руководство пользователя

Результаты поиска

Содержание PB00010R4N

Отзывы:

Похожие инструкции для PB00010R4N

Бренды по названию

Популярные бренды