ClearSpan PB00010R4N Скачать руководство пользователя страница 7

Страница: 7 / 29

CLEARSPAN

™

STORAGE MASTER

Revision date: 05.08.19

LAY OUT THE BUILDING SITE

After the site is prepared, identify the location of the shelter

corners to help square the frame after it is assembled.

Taking these steps

before

assembling the shelter saves

time and ensures that the structure is positioned as

desired. The following procedure is a suggested method.

Its use depends on the size of the shelter, shelter

application, the footings, and the method used to anchor

the shelter.

SQUARE THE SITE

1. Identify a corner where a building rafter will be

positioned, drive in a stake, and string a line the exact

width of the building and stake in place.

2. Sting a line at least as long as the building from the first

stake at 90°.

NOTE:

A transit can be used to ensure an accurate 90°

angle, or the 3-4-5 rule can be used. Refer to diagram.

Using multiples of 3-4-5 such as 6-8-10 or 12-16-20

helps to maintain an accurate 90° angle.

3. After squaring the position of the building and placing

a stake at all corners, string a line between the stakes

to mark the base of the building.

ASSEMBLE THE STORAGE MASTER BUILDING

COMPONENTS
NOTE

: Assistance is required to assemble the building.

RAFTER ASSEMBLY

Gather the parts:
•  Rafter pipe (26R1901)
•  Rafter pipe (26R1902)
•  Purlin end clamps (102857)
•  Band clamps (QH1404)
•  Tek screws
•  Magnetic nut setter 3/8'' x 2-9/16"

Rafter Assembly Procedure

Each rafter assembly consists of five (5) rafter sections:

four (4) swaged sections, one (1) plain section.
1. Select the five (5) pipes needed to assemble a rafter

and arrange these on a flat surface as shown below for

assembly.

2. Slide the swaged portion of each rafter pipe into the

plain end of the pipe as shown.

(26R1901)

(26R1902)

4. Continue with the rafter assembly.

Содержание PB00010R4N






























Результаты поиска

Содержание PB00010R4N

Отзывы:

Бренды по названию

Популярные бренды

ClearSpan PB00010R4N, Руководство пользователя

Результаты поиска

Содержание PB00010R4N

Отзывы:

Бренды по названию

Популярные бренды