Clean Energy CE-140 Скачать руководство пользователя | Manualshive

Страница: 21 / 78

background image

21

Oil storage tank setup:

Figure 16: Typical Oil Storage Tank Installation

(1) Refer to Figure 16 for a typical oil storage tank setup.
(2) The tank must be installed according to all NFPA requirements and State and Local codes.
(3) An inside tank is recommended.
(4) Locate the tank in a position that will allow the oil pump to be mounted as close as possible
(5) Only use a tank with a drain on the bottom. Over time, dirt and sludge will naturally
accumulate on the bottom of the tank and there must be a way of removing this unwanted
material.
(6) Some state and local codes require the tank to be vented to the outside.
(7) Educate all personnel what substances are allowed to be added to the used oil supply and
apply the provided tank warning label near the fill location.

Installing the metering pump system and oil lines:

Metering Pump Installation Guidelines:

(1) Use non-hardening thread sealer for all threaded pipe fittings. DO NOT use teflon tape.
(2) The pump must be installed with the shaft in the horizontal position and the oil outlet

pointing up.

NOTICE:

The gauge arrow on the front of the pump head must be pointing up.

CAUTION:

The metering pump must be mounted above the oil tank. The pump is

not designed to take head pressure. If the pump is below the level of oil in the tank the
pump seals may begin to leak.

FURNACE INSTALLATION

8

FT

. MA

XI

MU

M L

IF

T

SUCTION
OIL LINE

8" MIN

RELIEF
RETURN

CE70199

PRESSURE

OIL LINE

PRESSURE OIL LINE TO
THE HEATING EQUIPMENT

EMERGENCY

VENT

DRAIN PAN

WITH SHUT OFF
VALVE

CHECK VALVE

CLEAN OUT

VALVE WITH

PLUG

SUCTION OIL LINE IS ONE CONTINUOUS
PIECE OF COPPER TUBING INSTALLED
THROUGH THE SLIP FITTING

VENT

CAP

«
...
19
20
21
22
23
...
»

Содержание CE-140















































































Отзывы:

Нет отзывов

Похожие инструкции для CE-140

Бренд: Hotblast Страницы: 60

Бренд: Ducane Страницы: 4

CARBOLITE GERO 01964-5001

Бренд: VERDER Страницы: 32

Бренд: Carrier Страницы: 20

Бренд: Carrier Страницы: 16

Бренд: Airease Страницы: 58

Бренд: Daikin Страницы: 57

Бренд: ICP Страницы: 36

Бренд: ICP Страницы: 52

Бренд: United States Stove Company Страницы: 24

Бренд: WarmFlo Страницы: 37

WEATHER MARKER 58VCA

Бренд: Carrier Страницы: 13

CARBOLITE GERO CWF 12/23

Бренд: VERDER Страницы: 36

Бренд: York Страницы: 6

Бренд: Trane Страницы: 18

Бренд: Payne Страницы: 16

Diablo OFR Series

Бренд: Ouellet Страницы: 10

Advantage OFEA 000 Series

Бренд: Ouellet Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды