Clean Energy CE-140 Скачать руководство пользователя

Страница: 3 / 78

TABLE OF CONTENTS

SAFETY CONSIDERATIONS AND GUIDELINES.............................................................. 4

TIPS FOR MAINTAINING HIGH PERFORMANCE............................................................ 6

FURNACE ASSEMBLY....................................................................................................... 7

(1) Installing the blower........................................................................................... 7

(2) Air discharge configuration................................................................................ 10

- Unit Heater (Free Air with no ductwork)...................................................... 10

- Central Furnace (ductwork installed).......................................................... 12

(3) Installing the combustion chamber target.......................................................... 13

(4) Installing the burner........................................................................................... 13

(5) Installing the connector block and oil line.......................................................... 14

FURNACE INSTALLATION........................................................................... ..................... 15

(1) Selecting a location........................................................................................... 16

(2) Mounting the furnace in position........................................................................ 17

(3) Connecting the electrical supply........................................................................ 18

(4) Installing the chimney components................................................................... 19

(5) Oil storage tank set up ...................................................................................... 21

(6) Installing the metering pump and oil lines......................................................... 21

(7) Connecting the compressed air line.................................................................. 26

(8) Installing the wall thermostat............................................................................. 27

PREPARING THE METERING PUMP FOR START UP..................................................... 27

STARTING AND ADJUSTING THE BURNER.................................................................... 28

(1) Preparing the burner for start up....................................................................... 28

(2) Priming the oil pump.......................................................................................... 28

(3) Adjusting the Burner.......................................................................................... 28

RESETTING THE OIL PRIMARY CONTROL..................................................................... 29

SETTING THE DRAFT........................................................................................................ 30

MAINTENANCE.................................................................................................................. 31

SEQUENCE OF OPERATION............................................................................................35

TROUBLESHOOTING GUIDE........................................................................................... 36

FURNACE DIMENSIONS................................................................................................... 38

WIRE DIAGRAMS.............................................................................................................. 41

BURNER POWER SWITCH............................................................................................... 47

PARTS DIAGRAMS............................................................................................................ 48

CHIMNEY INSTALLATION DIAGRAMS............................................................................. 74

SERVICE RECORDS......................................................................................................... 76

WARRANTY INFORMATION............................................................................................. 77

Содержание CE-140















































































Результаты поиска

Содержание CE-140

Отзывы:

Похожие инструкции для CE-140

Бренды по названию

Популярные бренды

Clean Energy CE-140, Руководство пользователя

Результаты поиска

Содержание CE-140

Отзывы:

Похожие инструкции для CE-140

Бренды по названию

Популярные бренды