manualshive.com logo in svg

Clean Energy CE-140, Руководство пользователя

Поделиться
Скачать
Clean Energy CE-140 Скачать руководство пользователя страница 25

25

Installing the pressure oil line to the furnace:

(1)  Refer to Figure 21.
(2)  Determine the length of copper tubing needed for the pressure line (from pump to furnace)          
       and use the appropriate sized tubing.  If the pressure line is less than 100 feet, 3/8” copper  
       tubing can be used.  If the pressure line is greater than 100 feet, use 1/2” copper
       tubing.  An adapter fitting may be needed when using 1/2” copper to make the connection   
       between the tubing fitting and mini ball valve (50039 - 1/8 MNPT x 1/4 FNPT).

NOTICE:

 

There are installations that will operate well with a long pressure oil line.  However,

to ensure proper performance with variables such as oil temperature and viscosity, Clean
Energy Heating Systems does not recommend exceeding 150 feet of total pressure oil line. 

(3)  It is ideal to have the pressure oil line sloping up from the pump to the furnace.  This 
       reduces the risk of air pockets and nuisance shut downs.
(4)  Refer to Figure 22.
(5)  Connect the pressure oil line to the aluminum connector block on the side of the furnace.

NOTICE:

 

By connecting the oil line to the connector block, the swivel fitting is utilized which 

allows the front clean out door to be opened without disconnecting the oil line.

Figure 21:  Metering Pump Oil Line Connections

FURNACE INSTALLATION

CE70204

PRESSURE RELIEF 
RETURN OIL LINE TO 

THE TANK

MINI BALL

VALVE

ADAPTER
TUBE X MNPT

PRESSURE OIL LINE TO 

THE HEATING EQUIPMENT

Содержание CE-140















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды