manualshive.com logo in svg

Clean Energy CE-140, Руководство пользователя

Поделиться
Скачать
Clean Energy CE-140 Скачать руководство пользователя страница 33

33

MAINTENANCE

Figure 30: Cleaning Ash From the Heat Exchanger

CE70174

Flush the nozzle adapter heater block:

(1) Refer 

to 

Figure 

31.

(2)  Open the igniter hinge cover on the burner.
(3) Remove 

the 

electrode

(4)  Loosen the oil line swivel fitting with a 9/16” open end wrench. 
(5)  Disconnect the air line by pushing on the release ring and pulling the tube out of the fitting.
(6)  Disconnect the quick disconnect electrical connector.
(7)   Disconnect the 3/16” copper tubing for the oil gauge.
(8)  Carefully remove the entire aluminum nozzle adapter heater block from the burner.
(9)  Remove all the components from the nozzle adapter heater block.
(10) Remove all the plugs from the oil ports with a 5/32” allen wrench.
(11) Clean the nozzle adapter heater block in a parts washer.  A tube cleaning wire brush (rifle   
 

barrel cleaning brush) can be used to properly clean the oil ports.

(12) Blow out all passages with a compressed air blowgun.
(13) Put all the plugs and components back on the nozzle adapter heater block and re-install it   
 in 

 

the burner. 

Содержание CE-140















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды