Claydon HYBRID M3 страница 60 Скачать руководство пользователя

Страница: 60 / 66

CARE AND MAINTENANCE

OPERATORS MANUAL - HYBRID - M3, M4, M4R, M4.8 & M6

To change the front tine, simply remove the lynch pin and remove the 19mm pin, slide the entire tine out and

replace the entire tine with a new one. Refit pin and lynch pin.

When new, the steel of the tine protrudes beyond the Tungsten, this is to protect the Tungsten when

transporting new drills. After use the drill should be placed on wooden boards to protect the Tungsten.
Great care needs to be taken when lowering the drills onto hard surfaces.

CHANGING WEARING PARTS

IMPORTANT

IF WORK IS REQUIRED TO BE CARRIED OUT WHILST

THE DRILL IS RAISED, ENSURE A SUBSTANTIAL PROP IS

POSITIONED SAFELY UNDER THE DRILL PREVENTING

IT FALLING UNDER ITS OWN WEIGHT.

CHANGING LEADING TINE

Содержание HYBRID M3



































































Результаты поиска

Содержание HYBRID M3

Отзывы:

Похожие инструкции для HYBRID M3

Бренды по названию

Популярные бренды

Claydon HYBRID M3, Руководство оператора

Результаты поиска

Содержание HYBRID M3

Отзывы:

Похожие инструкции для HYBRID M3

Бренды по названию

Популярные бренды