Claydon HYBRID M3 Скачать руководство пользователя

Страница: 27 / 66

PRE-WORK PREPARATION

OPERATORS MANUAL - HYBRID - M3, M4, M4R, M4.8 & M6

Connecting the Drill to the Tractor

HYDRAULIC CONNECTIONS

The following decal can be found located on the front of the drill seed hopper. These decal’s specify the
corresponding hydraulic connections and their appropriate colour coding.

The return hose must be

connected before any hydraulic services are operated.

Connect the hydraulic hoses to the tractor spools in their relevant pairs. The

inch ISO female coupling

(freeflow return) with 18L male thread supplied with your drill

MUST

be connected to the rear of the

tractor. If necessary consult your tractors operators manual for correct freeflow connection on the rear

of the tractor (

Max 5 bar

). The free flow return pipe cannot just be inserted into the filler cap as the oil

cannot return to the pump sufficiently quickly on many tractors.

IMPORTANT

THE HYDRAULIC FREE FLOW & CASE DRAIN SERVICE

MUST BE PLUGGED IN PRIOR TO THE DRILL BEING

OPERATED FAILURE TO DO SO WILL RESULT IN

DAMAGE WHICH IS NOT COVERED BY WARRANTY.

Incase of difficulty knowing the correct connections available on the

rear of your tractor consult your tractor operators manual or Claydon

dealer immediately for assistance. Failure to connect tractor to drill

correctly can result in serious damage to hydraulic components on both

drill and tractor.

Do not change the

inch ISO on the free flow return to a difference size

as this could cause damage to the fan motor. The fan free flow return

cannot be connected to the tractor ISO.

Содержание HYBRID M3



































































Результаты поиска

Содержание HYBRID M3

Отзывы:

Похожие инструкции для HYBRID M3

Бренды по названию

Популярные бренды

Claydon HYBRID M3, Руководство оператора

Результаты поиска

Содержание HYBRID M3

Отзывы:

Похожие инструкции для HYBRID M3

Бренды по названию

Популярные бренды