manualshive.com logo in svg

Claydon HYBRID M3, Руководство оператора

Поделиться
Скачать
Claydon HYBRID M3 Скачать руководство пользователя страница 24

F

DIRECTIVE PROVISIONS

24

OPERATORS MANUAL -  HYBRID - M3, M4, M4R, M4.8 & M6

Directive Provisions

This Claydon Hybrid Seed Drill conforms to Machinery Directive 2006/42/EC (see Declaration of Conformity 
at the front of the manual).

AIRBORNE NOISE EMISSIONS

The A-weighted emission sound pressure level of measurements taken directly at the fan is 94dBA.

WARNING AND CAUTION

These warnings and cautions must be observed when operating the Hybrid Seed Drill. 

• Ensure total weight of tractor/drill combination does not exceed permitted limits and weight of tractor is 

sufficient for safe field and road use. 

• Do not allow anyone to stand between tractor and machine during coupling/uncoupling procedures. 

• For maintenance/adjustment of the machine ensure that it is lowered to the ground. 

• Seed dressing may be highly poisonous so protective measures-gloves, goggles, face-mask must be used while 
loading the hopper and cleaning the machine after use with compressed air. 

• The hydraulic system on the machine operates under high pressure. Pressurised hydraulic oil is dangerous 
so connecting/disconnecting the drill must only be undertaken with the tractor engine turned off and the 

pressure in the hoses released. 

• Before operating the machine ensure no-one is standing within range of its turning circle-including the 

marker arms. 

• The Tungsten points on the leading tines should be protected  when lowering onto concrete or paved 
surfaces by placing wooden boards under the tines.

Directive Provisions

!

WARNING SYMBOLS

Warning

 - Always pay extra attention to any text next to this symbol. This symbol could 

relate to something which can cause damage to the machine, serious injury or death. Please 

take the relevant precautions to avoid dangerous situations.

Eye Protection is required

 - In the interest of safety, eye protection must be worn.

Gloves are required

 - In the interest of safety, gloves must be worn.

!

Please Note 

- Information relating to this symbol may be worth noting as a useful tip to 

help use the machine more effectively.

Содержание HYBRID M3



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды