manualshive.com logo in svg

Claydon HYBRID M3, Руководство оператора

Поделиться
Скачать
Claydon HYBRID M3 Скачать руководство пользователя страница 37

37

H

IN FIELD OPERATION

OPERATORS MANUAL -  HYBRID - M3, M4, M4R, M4.8 & M6

SETTING THE SEED DEPTH

SET UP THE SKI BOARD

The Ski Boards should be set up to drag along the top of the ridges with little down pressure. The down 
pressure can either be increased or decreased by altering the adjuster at the rear of the drill 

(3)

. The  Ski 

Boards are designed to level the ridges created from the leading tine and not to perform any kind of pressing 
operation. The Boards should not be set at too steep an angle and should have the appearance of skiing along 

the surface. The harrow tines, standard fitment, may also be fitted to follow behind the ski Boards or used as 
an alternative depending on the machine specification. (See next page for recommended settings)

1.  Harrow tines 
2.  Ski Boards 

3.  Ski Board/tine adjustment

A quick guide to correct drilling depth is to check the A-Shares relative to the soils surface. The diagram 
below displays the recommended A-Share (2) depth for Oilseed rape (shoulder of A-Share should coincide 

with soils surface) and Wheat (top of A-Share should coincide with ground surface).

1.  Leading Tine

2. A-Share depth - OSR

1.  Leading Tine

2. A-Share depth - Wheat

Oilseed Rape

Wheat

1.

2.

3.

1.

2.

1.

2.

Содержание HYBRID M3



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды